Q:I know they can control networks but what about cable, what is keeping cable channels from just showing hardcore pornography 24/7even showtime has a no bottom/no thrust/no rod rule.I don't have HBO so I don't know what they use, but still do we really need the FCC to censor its obvious that tv channels aren't desperate to put porn on the air so why do we need the FCC (other the the frequency adjustments for radio and what not)

The FCC controls what is broadcast over the air waves. Cable TV is by subscription only, so if you don't like the programming you don't subscribe. Broadcast TV requires no subscription and is freely available to anyone who turns on a TV set. If the FCC were not there to control broadcast TV you would soon see porn popping up everywhere, since it is about the only thing that sells.

Q:which cables cant be near each other??(will cause noise radiation if put together)i gotta run some wires through my car and i dont know wich ones to keep away from others. im runnin...4 gauge (eventually will be 2 gauge) power wire for amp2 speaker wires for rear deck speakersrca cables for ampremote turn on wire for amp

I was always told not to run power next to RCA cables. When I ran my cables I ran Power on one side and speaker and RCA down the other side in my car. It even says to do it this way in my amp instruction manual;Plan the wire routing. Keep RCA cables close together but isolated from the amplifier's power cables and any high power auto accessories, especially electric motors.This is done to prevent coupling the noise from radiated electrical fields into the audio signal.

Q:The power cable for my DELL laptop AC adapter just got burned. I read the power that the desktop cable transmits. It is the same as my laptop's power cable. Is there a real risk if I use it?

it is not good to use it like that, a new cable will be much better.

Q:i soldered in one of those ribbon cables on to my hp's laptop power button cause the old ribbon was failing. anyways i am having some issues with this new cable1 the laptop will power on by itself if i insert the ribbon into the motherboard connector2 the only way to power off the laptop is to remove the cable from the mother board connector and that means opening up the whole laptop3 like i said it will power on by itself so that means that i cant turn it on/off with the power buttonevery thing is soldered correctly i dont understand also i am not sure but does the cable have to be like the old one cause the new one i soldered in looks the same? could it be that it needs that one particular cable replaced again? please help me i am sad

Soldered where ? Most ribbon cables are never soldered.. They are designed for push / cold-weld fit to connectors And soldering the cable risks melting the insulation between the cores in it (as they are not designed for heat) if you solder the motherboard, you risk damaging the wires (and vires) in the several layers of printed circuits (they are quite fine, multi layered not dual external visible only) I suspect you have damaged the cable (internally) update: from those pictures, it is clearly meant to be purchased 'as an already assembled' piece What I suspect has happened, is that there is a small sliver of solder etc (or dirty flux) between the tracks. Those are really low current, circuits, so does not take much 'leakage' to cause a contact to 'appear' closed. Repairing such things, often requires a very very narrow soldering bit and also fine solder / flux. I have seen most people use a microscope to do those repairs before - due to the likelyhood of small bits getting in the wrong place (and tracking unexpectedly occur). A good flux remover / cleaner would be useful ? Is the cost a replacement button complete with cable not cheaper to buy (OKorder is my favorite location for PC parts, shipped in from HK typically)

Q:I need help asap before I lose my patience with my dog.

Try Radio Shack or if it has a 3 prong socket any computer power cable will work.

Q:holes to route the cable through anyone have pics or a website so i can figure it out

ye this is just a common problem on many cars/tucks not just ford. did a custom install on my jeep and had to cut small hole in front left insulation under dash. it came right out into open space under hood and made great place to run wire. if u cant see any holes/spaces to run it then ur gonna have to cut a hole ro have someone do a pro install for you. (ultimately its cheaper easier to diy - need power drill and a big enuf bit to fit wire thru. im sure u can figure it out, just go slow and be carful, mine worked quik and easy and sounds great. good luck w/ all that - hope i helped

Q:everything was working great! and then i blew the main fuse! i replaced it everything was fine after that but then out of nowhere i only have power in half of the power cable connected to the amp!! What can i do??

Not sure what power in half the power cable means. Are you saying (for example) you have a 6 foot power cable coming off the battery to the amp and only 3 feet has power and the other 3 feet doesn't? I would isolate the power wire from start to finish. I would bypass the power wire by running an external wire from the battery terminal to the amp. Basically, disconnect the old power wire from the battery (or source of power) and amp. Then run a temporary wire from the battery to the amp. If everything works then something is wrong with the original power wire.

Q:I have a Belkin Tune Cast II FM transmitter. The fuse in the DC car power cable is .5 A but it blows every time I plug it in. What is the correct fuse to use for this charger?

If you know that's the correct fuse. You might have another problem such as the wires are shorting or grounding each other out and not completing the circuit. It might just be best to buy a new transmitter instead of wasting your money on fuses.

Q:where can i buy a power cable for my Lexmark P350 series photo printer?

You can also contact Lexmark Technical Support at 1-800-LEXMARK to request for the Lexmark P350 photo printer power cord for free. Hope this helps.

Q:where do i put the wire through from the inside of the car to the battery located under the hood?

First, examine the vehicle for an existing penetration in the firewall that provides access to the engine compartment from the passenger compartment. If there isn't one, you will need to drill a hole in the firewall. Make sure you are not drilling into any wires or vehicle components and then drill an appropriately sized hole through the firewall. Place a rubber grommet in the hole and then thread the wire through the grommet. Try to find a grommet that fits snuggly on your amp power cable so it will help to keep the drilled hole as water tight as possible. Also drill the hole so that the grommet fits snuggly as well, don't drill it too big. Make sure to secure your power cable inside the engine compartmentso it isn't loose. Good luck!