1.MPPT and DSP chip technique 2. brushless DC motor. 4.C&U bearing
Specificaion Solar water pump consists of solar panel system, PV water pump controller system and pump. 1. Solar panel system: Solar arrays are in series-parallel ofsolar modules; transfer the solar energy power to electricity to supply power for pump system. 2. Photovoltaic water pump controller system: it regulates all the pump system, turning instable DC voltage of solar panel system into stable DC voltage for pump, and regulates the output current in according with sunshine intensity to achieve maximum power point tracking(MPPT), maximizing the use of solar energy. 3. Solar pump system: it consists of pump body, motor, water pipe, cable, protection devices, water level sensor.
Application: The solar pumps can automatically work in the day, while the sunshine is lower. So it is suitable for irrigation, garden, fountains, family, pastoral grasslands, mountain, especially working in the areas without electricity supply.
Products feature: 1. Water pump controller system has complete electrical protecting device, against under-voltage, over-voltage, over-flow, overload, waterless, etc; also with an automatic switch and water level sensor that can on/off the pump when the well is dry and the water tank is fully. 2. Pump head: 10-180m, Flow rate: 1.8-60M3/h. 3. Working temperature:-20-50
Service life: Solar panel: 20-25years; Pump comtroller: 10years Water pump: 30,000hours
Send a message to us:
Q:What are the important parameters of the pump?
The head is the unit weight of liquid pump pumping from the inlet of the pump (pump inlet flange) to the outlet of the pump (pump outlet flange) energy value. Effective energy is a Newtonian liquid through the pump unit is obtained. The N m/N=m, the height of liquid column pumping liquid used, referred to as meters.Speed nThe speed is the number of revolutions per unit time of the pump shaft. It is indicated by the symbol n. The unit is r/min.Cavitation allowance NPSHCavitation margin, also called net positive suction head, is the main parameter to indicate the cavitation performance. The cavitation margin has been expressed by delta H at homePower and efficiencyThe power of water pump usually refers to the input power, that is, the power transferred by the prime mover to the pump shaft, so it is also called shaft power. It is expressed by P;The effective power of the pump, also known as the output power, is expressed in Pe. It is the effective energy obtained by pumping the liquid out of the pump in unit time
Q:How to select hydraulic pump?
1. rpmOperating speed is the actual rotation speed of a pump (or motor) at work.Rated speed is the maximum speed that can operate normally for a long time under rated pressure. If the pump exceeds the rated speed, the work will cause insufficient oil absorption, vibration and noise, the parts will suffer cavitation damage, life expectancy.Minimum steady speed is the minimum speed allowed for normal motor operation. At this speed, the motor does not appear crawling phenomenon.
Q:What is the difference between an air pump and a water pump?
The air pump (Q. B ng air pump), namely "air pump", a device for removing air or add air from the enclosed space from a closed space. The air pump is mainly divided into an electric air pump and a manual air pump. Electric air pump. An electric pump powered by electricity; produces air pressure by constantly compressing the air through electricity. Mainly used in pneumatic rubber, car inflatable, etc..
Q:What are the main performance parameters of the pump?
The amount of liquid supplied by a pump in unit time. Volume flow Q, unit m3 / s. There is mass flow G, unit is kg / s.
Q:The distance from the pump button to the ground
After confirming that the fire pump has started running, issue a command signal to the hydrant button to light the green answer light.
Q:Water pump can not be pumped out, how to maintain water?
The pipe leaks or leaks:The nut may not pinch well when it is installed. If the leakage is not serious, it can be coated with cement or mixed with asphalt oil in the places where the gas leaks or leaks. Temporary repairs can be done with wet mud or soft soap. If the leakage at the joint, you can tighten the nut by hand. The leak is critical and must be re assembled.
Q:How is the pump level of submersible sewage pump determined?
Pump water level must be higher than the water pump top, so that the motor running in the lower water temperature cooling environment, otherwise long-term operation will burn the machine
Q:What is the pump, how to classify, mainly used in where?
2. other classification of pumpsThe pump can be divided into two parts according to the position of the pump shaft:1) vertical pump2) horizontal pumpDivided by the number of suction ports:1) single suction pump (single suction pump);2) double suction pump (double, suction, pump)According to the prime mover of the drive pump:1) electric pumps2) steam turbine pump3) diesel engine pump[other details]
Q:Pump unloading in hydraulic transmission,
Unloading is pumping oil directly back to the tank, the pressure is very low, energy saving
Q:Why is the sewage pump device coupler?
Advantages of installation and arrangement of sewage pump coupling:1. automatic coupling device, easy installation and maintenance. In the absence of automatic coupling device under the condition of fixed installation, such as pump fault maintenance personnel need to unscrew the screw pump lifting water, repair, or other small pump to pump the water down perfect maintenance, if the water is dirty, it would be difficult for people to go to the next, then the overhaul had great difficulty.