Q:How do i use a valve spring compressor. It looks like a c-clamp, so don't tell me how to use a smaller one, but the bigger one.Thanks

The forked end goes over the valve retainer, the flat end with the screw goes against the valve face. Simply close the handle to compress the spring. You may need to adjust the width of the jaws to fit the retainer and adjust the length of the screw to compress the spring the right amount. Sometimes it helps to gently tap the edge of the retainer with a hammer to loosen the keepers before compressing the spring.

Q:I HAVE A 2003 FORD EXPEDTION THAT IS IDLE ROUGH,AND WILL EVENTUALLY STALL. TODAY I FOLLOWED THE PCV VALVE HOSE TO THE BACK OF THE THROTTLE BODY AND NOTICED THERE IS A BIG HOLE ON THE ELBOW OF THE HOSE. HOW CAN I CHANGE IT? CAN I JUST FORCE THE HOSE OUT AND SIMPLY PUT A NEW ONE? BEEN HAVING THIS ROUGH IDLE /STALL PROBLEM FOR A WHILE I CLEANED IAC VALVE, THROTTLE BODY CHANGED THE AIR FILTER AND ALSO CLEANED THE MASS AIR FLOW SENSOR, I HAVE A P0171 system to lean(bank 1) code

So, the rubber elbow hose has a hole in it. Your best bet is to get the replacement from the Ford dealer. Yes, you can buy just the elbow part from the parts counter at the dealer. If they start acting all dumb (and won't help you or sell you the part) then, go to a different dealer for the part. Another thing you could try is a used one from the junk yard BUT, it's been my experience that the rubber gets too hard and the PCV valve needs a lot of encouragement to be removed. Sometimes you'll damage the used elbow by trying to get it off of the engine or removing the old PCV valve to put in your replacement valve. That's why I recommend getting a new one straight from the source. They are pretty simple to change with ordinary hand tools and some mechanical know-how. You just pull the elbow off of the port that it's attached to on the engine. The valve will probably have a steel clip that goes around the hose at one end of the valve inside of the hose. You simply squeeze the clip with a pair of pliers and tug at the valve until it comes out of the elbow.

Q:Butterfly valve in use when should pay attention to what problems?

After the last in the pneumatic butterfly valve after use, also need to be cleaned immediately after the valve is closed, should use soft cloth to clean the valve, which may have some impurities, dirt removal, and oil lubrication, so it can better guarantee the use of the next.

Q:What is an electric two position butterfly valve?

Electric double position butterfly valve belongs to a kind of electric valve and electric control valve. Double eccentric flanged butterfly valve, compact, the product can be used as pipe system shut-off valve, control valve and check valve. With manual control device, once the power failure occurs, you can temporarily manually operated, and will not affect the use. 90 degree rotary switch is easy, reliable and long service life. It is widely used in water supply, power plants, steel mills, paper making, chemical, catering and other systems for water supply, as a regulation and cut-off use.

Q:e.g. a patient with a prosthetic aortic valve and a patient with a prosthetic mitral valve. Also, can you get stenosis of mechanical valves or just tissue grafts?Thanks!

mechanical okorder /

Q:i was changing valve seals and two dropped i can see the head of the valve but a magnet wont pull them up i put air the spark plug hole too but no luck 1985 ford bronco II

Your going to have to pull the heads.

Q:How warm is the PTFE butterfly valve?

Ordinary PTFE clip butterfly valve normal temperature tolerance of about 120 degrees, instantly to about 150 degrees

Q:What's the difference between cut-off valve, gate valve and butterfly valve? What's the difference in the working principle?

Stop valve is closed parts (valve) moving along the centerline of the valve seat, the valve stem to open or close the trip is relatively short, but very reliable cut off function, and because changes in the valve seat and the valve stroke is proportional to the amount of adjustment is also very suitable for convection.Check valve: also known as counter flow valve, check valve, back pressure valve or one-way valve, such valves are dependent on the flow of the pipeline itself flow force and automatically open and close, belonging to an automatic valveButterfly valve: it is a kind of valve which uses disc type opening and closing parts to turn back and forth about 90 degrees to open, close and adjust the passage of fluidGate valve is closed parts (RAM) along the vertical axis of the mobile channel valve in the pipeline, used primarily as a medium cut that open and close, generally do not have to do with traffic regulation, it can be used for low temperature and low pressure can also apply to high temperature and high pressure, and according to the different valve material is different in various media. The valve, the valve is the most widely used.

Q:What is the principle of butterfly valve and check valve? Any difference?

Crown valve pressButterfly valve is butterfly valveThe check valve is a check valveButterfly valve is mainly switching functionThe check valve mainly stops the pipe from flowing backwardsThe two can only be said to be valvesThe others are different

Q:The difference between butterfly valve and gate valve

Its varieties and quantities are still expanding, and the development of high temperature, high pressure, large caliber, high sealing, long life, excellent regulation, as well as multi-function development of one valve. Its reliability and other performance indicators have reached a high level. Disadvantages, there is a certain resistance to the medium. Gate valves are more used in steam pipes and large diameter water supply pipelines, because of the general requirements of fluid resistance is small, the use of gate valve. Valve is hand wheel rotation, stem upward movement. Flow is not the same, the gate valve requires full open. Need a higher installation space, the valve sealing surface has a certain self sealing capacity, its spool by the media pressure closely with the valve seat sealing surface contact, to achieve tight leakage.