Safety Metal Steel Door for New Design Decoration

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
2000 set
Supply Capability:
200000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

SECTION DRAWING OF SECURITY DOOR

1.Once-formed door frame

2.Three-head Top-Lock

3.Two -head Side-Lock

4.Reinforcement plate welded in the position of main lock.

5.Steel doorsill

6.Hinges

7.Invisible alarm doorbell

8.Peephole with wide range of 200 degrees

9. After being pickled, phosphorized and rustproof, the surface of panel also adopts hot timber grain transfer-printing treatment.

10.Door faceplate

11. The inner fillings: honeycomb paper.


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Aluminum alloy door seal lush dripping drip how to do?
Like this situation is generally the lower frame material level to play drainage holes or drainage holes are too small, there is a situation is not the location of the drainage hole caused by a rain caused by the indoor under the box material leakage of water leakage situation. This situation can be their own solution, but also to find the master of the doors and windows to solve. The solution is the same. That is, in the lower part of the box on the outer edge of the left and right to open a drain hole. Note; can not open a drain hole, because the wind pressure problem, open a wind pressure water or row does not come out, so open two. Drain hole can not play too deep, just penetrate the profile wall can be, whether it is flat window or sliding window position to play in the lower frame on the plane can be, do not hit the interior of the profile chamber. tool. Hand drill, 5mm twist drill bit.
Q:Which brush or roller should i use to paint my metal door?
Spray painting the door would be best. If you decide to roll the door, you need to use a very short nap on the roller. You will find rollers meant for smooth surfaces. That is the type of roller you want. A thick or deep nap will leave a rough texture in the paint.
Q:Home to install aluminum doors and windows, want to buy their own aluminum and glass DIY
The program is too much I suggest you or to do the aluminum alloy doors and windows to do the place now expensive! If you do not worry about the next year when the price is doing!
Q:What tools are needed to install aluminum doors and windows?
Cutting machine hand and so on
Q:Aluminum alloy doors and windows corner code used in doors and windows where the position
Mainly used for aluminum alloy profiles and profiles on the connection
Q:In microwaves ovens, can such waves pass through wooden or metal doors?
microwaves cannot pass through metal at all. even tin foil. the door of the microwave, as you might notice, has a sheet of metal with a bunch if round holes in it. the holes are just small enough that the microwaves cannot pass through them. as for the wood it would depend on what size. i don't believe that the microwave would pass through a piece of wood thicker than 1/2 inch. microwaves only penetrate food about a half to one inch. they cook the food by exciting the water molecules in the food and causing internal friction. the friction then spreads throughout the food. the wood should be enough to stop the waves. if you want to perform a science experiment put a glass of water in a wooden box and microwave it. the wood might get slightly warm as there is some water in wood. but if the water does not heat up then you would have your answer.
Q:Aluminum doors and windows of the airtight is divided into several grades?
If you do their own doors and windows do windows and doors recommended to do plastic doors and windows it, affordable, good sealing, the price of 140 or so, aluminum bridge on the bridge of the good, the price of 500 yuan a square
Q:how paint metal door
Careful surface preparation, sandind down with progressively finer sand paper, then use a sandable primer formulated for metal then resand with very fine sandpaper or emery cloth then spray paint for the best finish
Q:Interior chrome/metal door handles?
They use vac metallized plastic handles in acuras...and they're fine. A local machine shop can make you new handles if you take them off but they'll say something similar to dude...it's a door handle on an 18 year old car then charge you 50-60 bucks for custom work (no installation)... They don't really mass manufacture a metal replacement because it's not something people worry about.
Q:Aluminum doors and windows have unpleasant smell, how to do?
Should be low-cost glass strips, it is recommended to use ternary ethylene-propylene tape, plastic content is not less than 30%, we Qingdao million and doors and windows is EPDM 30% of the amount of glue, we million and the use of EPDM rubber strips are stamped on the tape in Qingdao million and doors and windows curtain wall company dedicated products, so can live in the quality of doors and windows, of course, the price can be higher!

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range