One Layer Steel Wire Rubber Braided Hose
Construction of one layer braided hose :
Inner tube: Oil resistant synthetic rubber
Reinforcement: 1 high tensile steel wire braided
Cover: Oil, abrasion and weather resistant synthetic rubber
Working temperature: -40C ~ +100C
Application of one layer braided hose
Widely used in all kinds of hydraulic engineering machinery, coal, petroleum chemical industry, construction, transportation and other industries
Specification of one layer braided hose
4.6 - 5.4
11.9 - 12.5
6.2 - 7.0
7.7 - 8.5
14.6 - 15.4
9.3 - 10.1
16.7 - 17.5
19.8 - 20.6
23.2 - 24.0
- Q:What are the categories of rubber products, rubber raw materials and rubber products?
- Hose type: pure hose, clip fabric hose, cotton woven hose, steel wire braided hose, steel wire winding hose, suction hose, etc..Tape products: rubber boat, lifeboat, vest, diving suits, anti wear, resistance to acid rain coat, ray clothing, lifting bag, storage water heater, air duct, inflatable, inflatable bed, raincoat, aircraft fuel tank.Rubber shaft roller: all kinds of plastic shaft, printing rubber roller, printing and dyeing rubber roll, paper, rubber roll, etc..Cable wires: all kinds of cables and wires made of rubber.
- Q:What's the effect of the shock absorber?
- It is the material of plastic and rubber, the buffer, shock absorber, that is to say in the pressure angle intact in your some deceleration zone, he will be your car completely after landing in the tire will help you to trace the body feeling, especially good for comfort.
- Q:Full coverage of car mats that kind of material better?
- The fully covered floor mat is developed on the basis of large surround and is now the most popular car floor mat. Fully enclosed mat Market, the use of synthetic leather or microfiber skin, natural rubber synthetic PVC, natural environmental protection synthetic rubber XPECommon automotive full cover mat materials are leather, rubber, VSQ, PVC, environmental protection, XPE and super fiber skin.
- Q:How can you clean up the double sticky tape on the instrument panel?
- If traces of glue has dried, only a little scratch, if not dry, first with nail hang double-sided adhesive glue, traces with a lot of cooking oil wipe can be gradually solved, or with a high concentration of ethanol wet wipe gently, effect of the two methods in general but can clear, but not to hurt the panel.
- Q:What's the tire composition?
- Tires are often used in complex and demanding conditions. They are subjected to various deformations, loads, forces and high and low temperatures while traveling. Therefore, they must have high load-carrying performance, traction performance and cushioning performance.
- Q:What is the rubber ring outside the wheel bearing of the battery truck?
- Is used to protect bearings, usually two kinds of materials
- Q:How to maintain the door seal?
- First of all we should timely check the sealing is not dust attachment, if any, should wipe with neutral water soaked cotton slow, do not use acid or alkaline water, in order to avoid corrosion of seal, and then check the seal is not a crack, is not broken. If this is the case, the adhesive can be used to repair it. In general, the adhesive will be used to mend the sealing strip, even if it is a big crack. If the damage is serious, you'll need to consider replacing it!
- Q:What is the swelling glue used in automobiles?
- Typical use:The utility model is suitable for the shock absorption and bonding between the automobile sheet metal and the stiffener, the framework and the support frame. Shock absorption of door, body, outer panel, outer panel and frame.Advantage：Easy construction, excellent adhesion on oil surface.High expansion rate, good adhesion, elasticity, sound absorption, shock absorption and noise reduction results from tightness.
- Q:What are the factors that cause the aging of automobile rubber parts?
- Transfinite. Some parts of rubber work in the process of long-term extrusion, deformation, or withstand the pressure beyond the design expectations, for a long time may lose flexibility, resulting in deformation, can not be used.
- Q:The car tire is pressing on the stone, the rubber of the tire is all broken, the heroes see can still use?
- The advantage of the patch method is that the patches are strong and do not hurt the crown. However, because the patch is from inside the tire, the tire hole still, so the water may damage from the immersion wire and ply; and, if the hole is large enough, sand and other sharp objects from the hole of the patch may be punctured, it is only suitable for small tire damage. Also, due to the internal patch will tire unloading, separation of tires and wheels, mended to go, so a long time to complete the whole tire.
1. Manufacturer Overview
|Annual Output Value
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
|No. of Production Lines
|Product Price Range