Rubber Fuel Hose Cover Braid,EPA,CARB Approved High Pressure
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 m
- Supply Capability:
- 500000 m/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
One Layer Steel Wire Rubber Braided Hose
Construction of one layer braided hose :
Inner tube: Oil resistant synthetic rubber
Reinforcement: 1 high tensile steel wire braided
Cover: Oil, abrasion and weather resistant synthetic rubber
Working temperature: -40C ~ +100C
Application of one layer braided hose
Widely used in all kinds of hydraulic engineering machinery, coal, petroleum chemical industry, construction, transportation and other industries
Specification of one layer braided hose
I.D | O. D | W.P | Test Pressure | B. P | Min. Bend Radius | Weight | ||
inch | mm | mm | psi | bar | bar | bar | mm | kg/m |
3/16 | 4.6 - 5.4 | 11.9 - 12.5 | 3045 | 210 | 420 | 840 | 89 | 0.2 |
1/4 | 6.2 - 7.0 | 12.7 -13.5 | 2784 | 192 | 384 | 768 | 102 | 0.25 |
5/16 | 7.7 - 8.5 | 14.6 - 15.4 | 2538 | 175 | 350 | 700 | 114 | 0.31 |
3/8 | 9.3 - 10.1 | 16.7 - 17.5 | 2277 | 157 | 314 | 628 | 127 | 0.36 |
1/2 | 12.3-13.5 | 19.8 - 20.6 | 2030 | 140 | 280 | 560 | 178 | 0.45 |
5/8 | 15.5-16.7 | 23.2 - 24.0 | 1523 | 105 | 210 | 420 | 203 | 0.52 |
3/4 | 18.6-19.8 | 26.9-27.7 | 1262 | 87 | 174 | 348 | 241 | 0.65 |
1 | 25.0-26.4 | 34.6-35.4 | 1015 | 70 | 140 | 280 | 305 | 0.91 |
1 1/4 | 31.4-33.0 | 43.3-44.1 | 624 | 43 | 86 | 172 | 419 | 1.3 |
1 1/2 | 37.7-39.3 | 49.7-50.5 | 508 | 35 | 70 | 140 | 508 | 1.7 |
2 | 50.4-52.0 | 62.4-63.2 | 377 | 26 | 52 | 104 | 635 | 2 |
Buying Guides:
SAE30R2 | Coupled and Uncoupled Synthetic Rubber Tube and Cover |
SAE30R3 | Lightweight Braided Reinforced Lacquer, Cement, or Rubber Covered Ho |
SAE30R5 | Wire Inserted Synthetic Rubber Tube and Cover |
SAE30R6 | Low-Pressure Coupled and Uncoupled Synthetic Rubber Tube and Cover |
SAE30R7 | Low-Pressure Coupled and Uncoupled Synthetic Rubber Tube and Cover |
SAE30R8 | Low-Pressure Coupled and Uncoupled Synthetic Rubber Tube and Cover |
SAE30R9 | Fuel Injection Hose Medium-Pressure Coupled and Uncoupled Synthetic Rubber Tube and Cover |
SAE30R10 | In-Tank, Low-Pressure, Uncoupled Fuel Hoses |
SAE30R11 | Low Permeation Fuel Fill, Vent, and Vapor Hose |
SAE30R12 | Low Permeation Fuel Feed and Return Hose |
SAE30R13 | Diesel and Biodiesel Fuel Feed and Return Hose |
SAE30R14 | Low Permeation, Low Pressure Coupled and Uncoupled Synthetic Rubber Tube and Cover Hose for Small Engines |
- Q:How about a rubber bar in a lathe?
- If there is a hole before drilling, and then a car axle with a front end of wire, plug in the positioning screw presses the car round, because the soft rubber car so that the car does not bend round hole, the above refers to cooked soft rubber, such as rubber is relatively hard point tool sharpening processing on the line!
- Q:What's the rubber tube on the empty filter for the motorcycle?
- Scooter engine case and even a larger pipe, the ventilation tube.
- Q:What is the function of the automobile exhaust lug?
- Fix the muffler and exhaust pipe tail section to avoid exhaust shock, affecting the body.
- Q:The side tire of the car has been knocked off a block of rubber. Can it be used?
- There is no steel wire on the side of the tire. The side injury is most dangerous. I suggest changing this tire as a spare tire. Especially don't run high speed.
- Q:What is the difference between the bottom rubber and the foot pad?
- Car Ottomans: most of the general, after the owner of the installation, there are special car. Fabrics are divided into velvet, thick and thin, and one is plastic or rubber, with transparent opaque. This kind of foot pad is easy to clean in the car. General Xianpu is a common velvet pad, a set of transparent. Choose a transparent pad to choose the quality, very soft, there is no smell.
- Q:What kind of material is good for heat shrinkable tube of automobile air conditioner?
- There should be four layers of material: 1, the innermost layer is Niron; the 2 layer is chlorinated butyl rubber (CL-HR); 3, the middle layer of polyester fiber reinforced layer; 4, the outermost layer of ethylene propylene rubber (EPDM)
- Q:Method for machining polyurethane rubber by lathe Too elastic
- Choose the higher hardness of the plate or bar, the processing speed is slow, so that processing is easy to point
- Q:How do I remove the glue from my car floor mats?
- Latex car mats using for a long time, because the bacterium, cause odor increase, so the depth of the cleaning work is very necessary, the best cleaning method of latex car mats, detergent, fruit is the best goods scented detergent, do not use detergent washing powder and other strong corrosive. That will only make the latex mat gradually yellow and not up to going to taste the effect.Through the introduction of the above methods, the owners buy new car mats, odor can be removed basically. In addition, pay attention to buy high-quality latex made from mats.
- Q:What kind of material does the automobile belt make?
- Timing belt is an important part of the engine air distribution system. It ensures the accuracy of intake and exhaust time through the connection with the crankshaft and with a certain drive ratio. The use of a belt rather than a gear to drive, because the belt noise is small, accurate transmission, small changes in its own, and easy to compensate. It is obvious that belts must live longer than metal gears, so wear belts regularly.
- Q:Rubber car Block for parking spaces. Where is the parking space?. What is the size of one side of the parking space?
- In fact, there is a relatively simple way to curb parking, that is, in front of the entire parking lot in front of the flat car in front of the line, according to the distance between the two vehicles, the width of the road and parking spaces set length. Then turn the steering wheel close to the point position back to the right until the front of the car close to the front right corner of the car, the left rear corner, the steering wheel starts to rotate. Initially, the steering wheel rotates slowly, when the front bumper in the front of the car leaves the steering wheel to the left, near the point position. From the left rear view mirror, the left rear side of the upper left corner of the car is aligned with the car, and the steering wheel is quickly reversed and stopped. The rest is just right. The car can be parked in the middle of the parking space.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Rubber Fuel Hose Cover Braid,EPA,CARB Approved High Pressure
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 m
- Supply Capability:
- 500000 m/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products