Roto-jet Pump

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT or LC
Min Order Qty:
1 unit
Supply Capability:
1000 Sets Per Month unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

began to develop rapidly. According to the type of working fluid jet pump can be divided into liquid jet pump and gas jet pump, among them with water jet pump and steam jet pump is most commonly used. Jet pump is mainly used for transport the liquid, gas and solid content.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Does the oil pump plug cause less oil?
The oil pump plug will not cause any reduction in engine oil, which will only result in the following two results:1. oil pressure drop, oil flow decreases, the appearance of insufficient lubrication2., serious blockage will cause oil in the oil pipe can not flow, causing the normal operation of the components to form "dry grind", accelerating the wear rate of parts
Q:How does the motor pump exhaust the air?
The oil pump is not required to take the air, booster pump, brake pump, water pump, clutch pump is the need to take the air, air film method is complicated, the need to add new oil, suggest you go directly to the repair shop repair station
Q:Does the abnormal oil pump affect power?
Hello, oil pump damage will result in lower oil pressure, engine noise, and accelerate the wear and tear of the car to start the internal parts
Q:Manual transmission, organic oil pump, automatic, stepless?
There is no oil pump in the manual transmission, there is automatic, that is, the non-polar.
Q:How to change the oil pump 1.8 MAGOTAN
The oil pump is usually installed in the oil pan.1, drain oil2 、 oil drain bottom shell3. Change the oil pump4, restore (refueling)
Q:How do you install the pedal motor pump?
Put the unit on the foundation with anchor bolts, between the base and the base, and use a pair of wedge pads.Release the axle shaft and place on the pump shaft and base with a level gauge. Adjust the level of the machine by adjusting the wedge pad and tighten the anchor bolts properly so as not to move around.Correct the concentricity of the pump shaft and the motor shaft, and allow the deviation of 0.1 mm on the outer circle of the axle shaft; two the clearance of the coupling plane shall be guaranteed 2~4 mm, and the clearance shall be uniform, and the tolerance shall be 0.3 millimeters.After connecting the pipeline and determining the direction of the motor rotation, then coupled with the coupling, and then check the concentricity of the shaft.In the actual test run 2~3 hours after the unit, for final inspection, if there is no adverse phenomenon, that the installation of qualified. Check the temperature and vibration of the bearing during the test run.During installation, all holes in the unit shall be covered to prevent debris from falling into the machine.In order to prevent the sundries from entering the pump, the filter shall be installed on the newly installed pipeline. The effective cross section shall be 2-3 times larger than the cross section of the suction pipe.However, the oil pump rarely fails, generally as long as the opening of the cylinder head, see more fresh oil or start the engine, there is oil jet, indicating the normal operation of the oil pump.
Q:In the 1 to 2 seconds when the vehicle is started, does the oil pump inject engine oil into the engine?
The first problem: the oil pump and the engine crankshaft movement synchronization, start the machine work a few seconds, the oil pump oil pump in the same way, just because the empty oil engine cooling period, not immediately to the oil pump in place.The second question: basically, there is no such operation necessary, when the engine does not run, the oil pump will not pump out oil, reduce the wear and tear of little effect, but more start will increase the wear of the starter.
Q:Automobile oil pump fault
Such a problem can arise. The oil pressure is too high, and the oil filter is opened by "drum". The reason is that the oil pump pressure limiting valve [pressure relief valve], resulting in a failure, can not normally open at high pressure caused by pressure relief.
Q:SUZUKI motorcycle oil pump is not on the oil, the circuit is not blocked, to replace the oil pump
Is the oil filter and the oil filter plugged? Is the filter core apron missing? How do you make sure there's no blockage? No reason for the oil is only the oil pump damage, filter, filter or oil clogged, lack of oil and several other reasons.
Q:How to solve the blockage of the automobile oil pump?
Gasoline pump, pump can not afford oil, may have the following aspects.1, the circuit is not smooth, this is very good inspection, with Multimeter or test light on the plug, play the motor light, indicating that there is electricity, no lights, indicating circuit failure.2, circuit fault, first check the oil pump, relay and oil pump fuse, when motor, oil pump relay should be pulled in, there is voltage output. If there is no voltage output, consider the oil pump, relay, or computer circuit to the oil pump, or even a drive computer.3, if there is electricity, it is much simpler, pull out the oil pump, the oil pipe, motor. When oil is out, check that the pipe is blocked and the gasoline pump is removed without oil.4, the gasoline pump if there is no foreign body plug, then you can change it directly!
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.

1. Manufacturer Overview

Location Hunan,China
Year Established 2006
Annual Output Value US$5 Million - US$10 Million
Main Markets 59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Africa
2.00% Oceania
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port SHANGHAI,GUANGZHOU,DALIAN
Export Percentage 51% - 60%
No.of Employees in Trade Department 6-10 People
Language Spoken: English, Chinese
b)Factory Information  
Factory Size: Above 100,000 square meters
No. of Production Lines Above 10
Contract Manufacturing OEM Service Offered Design Service Offered Buyer Label Offered
Product Price Range High and/or Average