Refractory Raw Materials-Micro Silica Materials

Ref Price:
Loading Port:
Payment Terms:
Min Order Qty:
20 m.t.
Supply Capability:
1000 m.t./month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Dead-burned magnesite is selected from natural magnesite, calcined temperature and the shaft kiln. It is the material of ordinary magnesia bricks, shaped and unshaped refractory products.


 It is used for steelmaking furnace bottom and ramming furnace.It is made from high quality magnesia and high purity magnesia-dolomite clinker in appropriate granularity ratio, it has good sticking ability, low rebounding rate and high abrasion-resistance
Usually it is used for converter gunning repairs


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Can the teflon material resist fire?
It is belonged to the fire retardant materials. By UL-V0 grade
Q:What's the fire resistance test method of doors and roller shutters?
Fire resistance test method of doors and roller shutters: This standard specifies the fire resistance test method for roller shutter doors under standard fire conditions. The method is used to test the fire resistance of the ventilating duct when bearing the external fire (A duct) and internal fire (B duct). Fire resistance test of vertical ducts may be conducted referring to this standard. 1.Test specimen1.1 The test specimen is obtained by cutting from any part of the qualified metal tube unless otherwise relevant standard or mutual agreement specifies the cutting position of the metal tube. 1.2 Length of the specimen: L≈2.5D+50mm (D: outer diameter of the metal tube). The cut surface of the specimen must be perpendicular to the axis of the metal , and the seamed edge of the cut should be round off. Test method GB243-82 of metal tube necking 2. Test procedures 2.1 In the test, punch or press the metal tube into the tapered conical seat (see Figure) with a hammer or press machine, and make it uniformly diminished to the regulated shrinkage X which is calculated according to the following formula: Test method GB243-822 for metallic pipe necking: The inner wall of the seat cover used in the test should be polished, and has certain hardness and is coated with lubricating oil. Its conicity is 1:10, 1:5 or others in accordance with relevant standard provisions. If there is no provision, then adopt the conicity of 1:10. This standard is not suitable for: a) The pipeline whose fire resistance depends on the fire resistance of the ceiling; b) The pipeline with access door, unless otherwise the access door is included into the pipeline and tested together; c) The pipeline with two or three sides; d) Fume exhaust pipes;
Q:How much modulus is used as refractories material of sodium silicate.
Storage and use are very convenient, especially for mechanized and the evenly refractory material and the sodium silicatemodulus is generally...2. transportation. The appearance of product is pure white. Instant powdered sodium silicate, also known as instant sodium metasilicate.4 to 3, in powder form, automation. in the range of 3, hydrated sodium silicate
Q:What are the refractory materials above 1000℃
corundum would be fine
Q:Are there any differences between insulation and refractory materials ?
Refractory materials can resist more than 1200 degrees, some of which are not insulation materials, such as firebricks, which can directly contact with heat source, has little insulation effect. Ceramic fiber, high silica, etc. are all refractory materials which can insulate. Insulation materials with poor performance usually is lower than 800 degrees, which have large thermal resistance, and low thermal conductivity, high porosity. Thus they reduce the thermal loss. To put it simply, insulation materials store most of the heat and only let a small part of heat lose through the air, thus the heat has been isolated. Glass fiber, rock wool, flexible material for thermal insulation, etc.
Q:Who knows about the grade C fireproof door materials?
There are no differences in the interior materials of the grade A , B and C fire doors, they all use fire rock wool boards. The only difference is the thickness of built-in fire rock wool boards. The rock wool boards' thickness of grade A fire doors is 52 mm, that of grade B is 46mm, and that of grade C is 40 mm.
Q:How can refractory materials be divided?
There are many criteria for the classification of refractories.Just referring to a book about refractory.
Q:What are the chemical composition of refractory cement?
Calcium aluminate prepared by calcining as the main component. Aluminate cement takes bauxite and limestone as raw materials, alumina content of about 50% as the clinker. And it is a hydraulic cementing material made by grinding. Refractory cement is also known as aluminate cement.
Q:I know which material is the fire resistance rolling shutter door
Fire resistance rolling shutter door and ordinary roller shutter are basically same, the differences are: Its inner and outer sides are generally made of galvanized iron sheet, filling asbestos fireproofing material betwwen two layers of fire resistance rolling shutter door, and some fire shutter doors can be interlocked with the relevant fire control system, when the breaking out of fire , it can automatically "half-drop" and "full drop".
Q:who knows the requirements of refractory for forge furnace?
Here is the requirements of refractory for forge furnace: according to the chemical properties,casting fireproof materials are divided into three major categories: acidic, neutral and alkaline refractory materials. alkaline and neutral refractory materials are commonly used, such as alkaline magnesia-carbon bricks and burned magnesite bricks, magnesite-chrome bricks, magnesium-calcium brick, neutral high alumina brick, corundum brick, clay brick, etc., shapelessness materials include: castable refractory, ramming mass, gunning mix, coating, dry vibrating materials and so on! Hope my answer can help you.

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range