QJD Deep Well Pump

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What's a small soft pipe for a submersible pump in a fish bowl? How do you use it?
Filter pump for oxygen spray. If the filter pump water flow, you can throw oxygen flowers, you can not use. With that pipe, it's loud and kind of
Q:What is wrong with my Home Water Pump?
All good answerers here. I would drain down the pump, remove the pressure switch and also remove the nipple that it screws on to and clean it out. Now put the pressure switch and nipple back in. At the top of your pressure tank there is an air valve. Take a tire gauge and read the pressure. If your pressure switch was a 30/50 there should be 27 to 28 lbs of air in your tank. If water comes out, your tank is water logged and needs to be replaced. If it's low on add to 27-28 lbs. Hopefully this will take care of your problem, it not send more info about what happened. Pay attention to the readings your pressure guage. Good Luck!!
Q:Replacing water pump and heater...?
You said water pump so i am going to assume your on a well. pumps range in price from $400-$1200. depending how deep the well is.Then you have the charge for pulling the pump, scince you have the expensive part done I would replace the rotten old well pipe and pump cable.by the time your done your looking at a bill from $900.00 to $2000.00. sorry. before you jump into replacing the pump I would contact a well drilling company that also installs pumps.We know about pumps and pressure tanks than ANY stupid plumber.
Q:Why is water pumping cool water is normal, but when pumping hot water pressure and flow are very small?
Not sure about the LZ what is the specific type of hot water pump pump but it is flow and small pressure must be produced liquid vaporization of liquid vaporization two general situation is the pump pressure alternating is under positive pressure immediately into negative pressure is two high temperature liquid into the pump and to absorb mechanical heat due to the higher temperature is the centrifugal pump if so when the liquid from the inlet to the outlet end of the impeller is thrown when in the state of negative pressure and lower boiling point even if did not reach 100 degrees will boilIf the water pressure and flow rate of small vaporization significantly not only reach the requirement of the pump itself also has a lot of damage caused by mechanical damage is suggested to view the instructions to use if this situation is to contact the dealer in the allowable range of temperatureIf no water is not only the problem of vaporization conditions can be detected under normal pressure inlet check instructions when pumps are used in the allowed suction height within the position and I don't know if the pump there may be no open suction valve or discharge valve and pump parts prior to use at the beginning of irrigation is the first inside in order to produce self suction irrigation
Q:Help replacing water pump?
being a 78 it probably has a V belt instead of a serpentine belt. you loosen the adjustment bolt on the alternator and the long through bolt, push the alternator and the belt should come off. you will need to take the fan off, it should have 4 bolts to take out to remove the fan. then you take the hose off after you drain the radiator and take out the water pump bolts and pry off the pump. now before installing the new pump make sure the gasket surface is clean and dry. put some good sealer on both sides of the gasket. to keep the gasket from moving i use string like thread and tie the gasket on. put the pump in place, put the bolts back in and tighten them, put the hose back on, put the fan back on and tighten the bolts and refill the radiator. if you want good sealer use what i use. i use indian head shellac. once that stuff gets set up it won,t leak. auto zone sells it in a small brown bottle.
Q:pressure of a water pump?
you must use density*gravitational acceleration*height. density=1000kg/m^3 Gravity=9.8m/s^2 height=given=236 m 1000kg/m^3*9.8m/s^2*236m=2312800kg/(m*... = 2312800 Pa=2312.8Mpa hope this helps, looking at the units it all works out: N/m^2=kg*m/(s^2*m^2)=kg/(m*s^2)=Pa
Q:QDX is a submersible pump. What does "X" mean?
Q submersible pumpsD single-phase motorX downdraft
Q:how do you change a water pump and on 2002 pontiac grand am gt?
This should be a V6 engine correct. if looking at front of engine,toward the belt , the water pump is located behind pulley appox. 5 inches on the side toward radiator. highest pulley on right side of engine. Replacement can be performed easily without many special tools.. First loosens each of the pulley bolts on pump. Then release tension on belt and route away from pulley. Remove remaining pulley bolts and pulley , Water pump has 5 bolts holding it to cover assembly, Mark-index the way pump installs and remove. Clean all gasket material. Install new pump and gasket, refill system and to open air blled on cooler pipe near water pump to allow air to escape.
Q:Water pump on engine! A sure sign to fix or replace?
if its starting to drip coolant from it and it isn't a gasket you need to replace it ,they don't last to long once they start to leak,you can look at it and tell where the leak is coming from,i have seen a few on occasion that was leaking from the gasket where somone had replaced them and not got a good seal back on it,but most of the time your looking at repalcing the water pump,depending on what its on it can be a big job to do,good luck.
Q:How to replace water pump on a 93' Mustang 5.0?
This is a straightforward task that can be difficult for the novice, but it's not impossible. You will need basic automotive hand tools, wrenches, sockets in metric. Also, you will need a good shop manual for this car. A torque wrench is optional, most professional mechanics don't torque the fasteners involved with this job. Take pictures of the engine from various angles, it will help in reassembly. Don't forget to disconnect the battery also. Be certain to draw a diagram of how the serpentine belt(s) are routed around the pulleys, if no such aid exists on the radiator support. By all means buy a reputable brand NEW pump, don't bother with a rebuilt unit. With some mechanical knowledge and basic common sense you can do this, take your time, don't rush. Good Luck !

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range