Q:What are the 3M double-sided adhesive?

Foam material double sided adhesive (made of foam base material, double coated with acrylic rubber): such as 3M4920, 3M4026, 3M4032, etc.;Hot melt adhesive film: such as 3M615, 3M668, 3M669 and so on;High temperature adhesive tape: such as 3M244, etc..

Q:How to remove double adhesive on paper?

Get some petrol at the glue point. Or put ice in the refrigerator after the trial, try not.

Q:Coating process of organic silicon high temperature double faced adhesive tape. The substrate is PI or PET film.

PP forum, a lot of PET film information, there are many PET film and packaging printing friends

Q:Construction method of butyl adhesive tape

(4) tear off the insulating paper on the top of the Yongxing adhesive tape and press the metal plate on the upper layer of the interface into the jointOrderly extrusion joints, so that the joint bond firm, closed tight.(5) tighten the screws so as to bond the upper and lower bonding surfaces of the adhesive tape. (1) pre installed above the parapet gutter gutter, the cement surface clean, brushing and base treatment.(2) the primary treatment agent suspected solid after installation of the water board, to ensure that the installation is firm and closely combined with the wall.(3) the water board will wipe clean, paste on the joint water board and cement wall in Yongxing according to the order of a single sided aluminum foil tape, the bonding agent pressure;

Q:With the two convex lens, a cylinder, a ruler, transparent tape, double-sided tape do magnifier

5. Ask a friend to measure the distance between two magnifying glasses and record them.The opening is about 2.5 cm near the front end 6, a cylinder in the local shear groove. Do not shear the reels. The slot should accommodate the larger magnifying glass.7, the paper then cut a groove between the groove and the first groove distance equal to the distance recorded in your friends. This is where the second magnifying glass is placed.8. Place two magnifying glasses on the appropriate slot (big ones in front, small ones at the back) and fix them with tape.

Q:How do you remove the double adhesive tape on the towel? Sticky very tight ~ ~ how to do?

1, with eraser along the edge of a little to rub inside, easy to trace. But depending on how sticky you are, it may vary in time. If conditions permit, the alcohol + eraser works very well2, you can take a piece of vinegar coated dry cloth to cover the entire double-sided glue mark place, and until the double-sided adhesive after soaking wet, you can easily remove with a ruler.

Q:PE foam double-sided adhesive tape for use?

Suitable for photo decoration, furniture decoration, car decoration, wave plate, baffle plate, round arc, brake lights, car logo,

Q:Does anyone know without leaving adhesive tape for a long time after, I see a company to buy a new printer with the blue tape torn left no residual, does anyone know what is this tape?

Scope of application: large area of difficult to remove offset printing, but if it is not often encountered adhesive tape traces of this kind of trouble, there is no need to specifically buy a bottle, with the author's small coup on it. The production process of mesh reinforcing double-sided tape, double-sided tape, Rubber double-sided tape, double-sided tape, high temperature, no glue non-woven double-sided tape double-sided tape, double-sided tape, double-sided paper glass cloth tape, PET double-sided tape, foam tape, hot melt adhesive tape, conductive tape, PET tape, masking tape, electrical tape, high temperature resistant tape, Mara tape, no backing tape, acetate cloth tape, PVC tape and other applications in all walks of life in;

Q:What kind of double faced glue is used at the bottom of the glass panel and the glass panel? How do you glue it?

Most of the sides between glass panel and cooker bottom are ordinary double faced adhesive tape, but the width, thickness and color match are more coordinated. When bonding, the adhesive tape is glued to the upper edge of the shell, and then the panel is gently covered. It is possible to compress the screws around the head of the furnace before it is fixed in place.

Q:How to fill in the property when releasing adhesive tape?

First of all, to understand your kind of tape, that is, its use, and then define attributes. I hope I can help you!