Q:A good way to protect the corners of the horns

Corner corner according to the use of the location is divided into: angle angle angle (angle installed in the protruding corner, mostly large hole section of the angle of more than 90 degrees), corners of the corners (corners installed in the concave The corner of the corner, the majority of small round hole, section angle of more than 90 degrees.), Can be bent corner, T-type angle; angle can also be divided into: insulation angle and decoration corner, Winged corners of the mesh material is attached to the metal or PVC profiles on both sides of the role, play a role in the stucco, wingless corners is in the metal or PVC guide profile drilling, so that the corners directly embedded Stucco.

Q:Why do the construction before the plaster angle

Hole protection angle is the protection measures, construction before the wiping angle is plastering construction order. Interior Plastering Construction Order: Pouring Wall - Cleaning Base - Paste Cakes - Punching - Bottoms - Leveling - Wiping

Q:Whether the wall angle is all need corners

Corner surface can not be sticky transparent tape or the United States and paper and other sticky material, and the surface of the paint reaction, loss of luster or paint.

Q:How to install wooden corners

Shaped corners, take the world, equipment, decoration, auxiliary, material plant

Q:What is the cement corner when plastering?

Will be used in square feet square, side of the window frame side to frame wall void prevail, the other side to tendon thickness prevail, in the ground to draw a good line, according to the thickness of the plaster layer sticky stickers and with a tray board hanging vertical. In the other side of the edge of the edge of the corner of the wall of the pad of cement mortar, the outer corner and the outer edge of the plate with the flush; side of the wipe after the board to move to the side of the card to stabilize, and hanging vertical Straighten the ruler, the corner of the other side of the cement mortar layering wipe; and then gently removed by the foot board. To be a little corner of the corner after a little water, with Yang angle trowel and plain cement wipe the small rounded corners. And finally left on both sides of the corner angle width, the excess mortar to 45 ° slant cut off.

Q:Can I put the tiles on the tiles?

Yes, the use of corners to help the corner of the construction, the operation is very simple, three steps to complete: The first step, will be mixed with cement slurry (white cement: white latex 3: 1, and add appropriate amount of putty powder) smear on both sides of the corner to be constructed; The second step, the corner against the corner, find the level or vertical, and then scraping the overflow of the slurry; The third step, dry and fixed after relying on the top of the positioning of the corner, and then scraping a layer of putty leveling can be. For indoor and outdoor decoration, in addition to the commonly used indoor yin and yang angle, there are cracks used to prevent cracking and repair cracks.

Q:White wall white door fitted with any color of the corner of the good-looking

installation method: 1, the wall is the original wall of cement. 2, a wall paint, and directly stick to the wall paint. 3, the glass glue or construction glue coated on the back of the horn, about 1 cm thick, point-like. 4, the wall as needed to do the mark, with 2mm thick double-sided adhesive attached to the back of the corner of the corner, the alignment mark on the wall, so that double-sided adhesive full contact with the wall, you can let go. But do not touch, until the glass gel can be used after solidification.

Q:Yang angle of the corner should be done more than meters

The corner is to prevent the use of the process of damage to the components, and in the normal use of the process of injury are basically the angle of the sun, taking into account the height of people and some accidental factors, so the height of the corners will be made from The ground from not less than 2m.

Q:My wall stickers wallpaper, two walls of the wallpaper between the angle of the joints, the wall angle not only to protect the corner, but also to suppress the wallpaper, to prevent the seam rolled up, then my wall is not corners And the wall as high, or the middle of the point on the line? And the wall as high as the unsightly, on the middle of the pressure afraid of the wallpaper curling, how can I do?

Look at your room other decoration, you need to cover all the aluminum can see, not stainless steel, this is the metal, and you and the style of your home do not match, and then press the half of the words, pressing the long encounter Height can be, 1.2 / 1.5 of a can, after all, will not always touch him.

Q:Which norms are staircase stepping angle using steel bars to do corners of the practice

I have not heard of this specification, only seen with copper bars do staircase corner. Because the steel exposed to the air is easy to rust, the volume becomes larger, will open the cement mortar, causing the paint layer cracking off. So in principle, should be used copper or stainless steel as well