PVC All Flange Tee

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
0.5 Ton
Supply Capability:
300 Tons per Month m.t./month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

PVC all flange tee  

The product has long life, excellent tenacity, corrosion resistance, and convenient application.

 

PVC all flange tee

1:Used for water piping

2:External coated with rich zinc plus bituminous paint

3:Internal coated with cement mortal lining

4:As per customer requirement painting zinc

5:processing technique: Sand cast and lost foam

 

Ductile iron  tee                                 

 usage

 Used for water piping

 coating

 

 

 External coated with rich zinc plus bituminous paint

 Internal coated with cement mortal lining

 As per customer requirement painting zinc

 processing technique

 Sand cast and lost foam

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What's the meaning of the plumbing PVC pipe joint specification "1/2" "X12" and "1/2" "x18"?
Plumbing PVC pipe joint specifications 1/2, "X12" and "1/2" "x18" these two specifications belong to the British unit.
Q:What joints do nylon hard tubes work on?
(two) clamp sleeve type pipe joint;Application: sealing pipe joint oil, water, gas and other non corrosive or corrosive medium, with plastic pipe specifications are flexible, and pipeline connection, has the characteristics of reliable connection, good sealing performance, so it is widely used in oil refining, chemical industry, light industry, textile, metallurgy, national defense, aviation, ship the system is suitable for all kinds of hydraulic transmission; mechanical engineering, machine tools and other equipment pipeline. Sleeve type pipe fittings manufacture standard following fifteen kinds:1, card sleeve end through pipe joint (GB/T 3733-2008)2, sleeve type cone thread straight pipe joint (GB/T 3734-2008)3, card sleeve type end through long pipe joint (GB/T 3735-2008)4, long taper pipe thread joint (GB/T 3736-2008)5, card sleeve straight through pipe joint (GB/T 3737-2008)
Q:Hot tap water pipe joint leakage, what method can be repaired?
The original hot connection place cut, a new joint with a pipe section, and then pick up
Q:I would like to ask who has 24 degrees taper hydraulic pipe joint processing drawings, please send me, thank you very much
If you can, then I have thousands of pipe joints drawings, are the original pipe joint processing factory technician to do when painting,
Q:The expansion type pipe joint and the sleeve type pipe joint difference, everybody looks at the picture, this is belongs to that kind of?
The material of the pipe has a problem, it is a hose. So what kind of form do you have?. If the straitjacket of words, should belong to flaredfitting.
Q:What's the difference between pipe repair device and clamp type flexible pipe joint?
The clamp type flexible pipe joint needs welding, but the pressure range is big, 10-220 kilograms of pressure can bear, and it has the limit function, at the same time provides the effective flexibility and the corner to the limit. The utility model is generally used on pipelines of more than 16 kilograms, and the cost is greatly lower than the flanges and the telescopic devices.
Q:What's the meaning of the pipe joint 14-M18*1.5? What's the thickness of the wall?
(two) prohibit adding sealant and other fillers. Some people in order to obtain better sealing effect, in the card cover with sealant, the result of sealant is poured into the hydraulic system, causing hydraulic components, such as plugging holes. (three) when connecting the pipe, the pipe should have enough deformation allowance to avoid drawing the tube. (four) when connecting the pipeline, the lateral force should be avoided, and the lateral force will cause the seal to be too tight. (five) when connecting pipelines, should be a one-time good, avoid repeated disassembly, otherwise it will make poor sealing performance. Sleeve type pipe joint installation (1) of the pipe should need pickling pickling treatment according to the ninth chapter; (2) tube machine equipment cut tube with special cutting or sawing machine according to the required length, absolutely not allowed by fusing (such as flame cutting) or grinding wheel cutting; remove pipe end burr, metal cutting inside. Dust and dirt; remove the rust and dirt pipe joint; and also to ensure pipe roundness; (3) the sleeve nut, successively sheathed in the pipe sleeve front edge (small end) from the pipe mouth at least 3mm, then the pipe is inserted into the connector body bore, top to check; (4) slowly tighten the nut, while rotating the pipe until does not move, then tighten the nut 2/3 ~ 4/3 circle; (5) open the check card sets whether has cut the pipe correctly. The clamping sleeve does not allow axial movement, but slightly rotates; (6) after checking, tighten the nut again.
Q:What does pipe joint "DD" mean?
Parts that work in a weak corrosive environment, such as covers, bearings, valves, hand wheels, etc., are joined mainly for connection, installation and maintenance.
Q:Can the sleeve type pipe joint be disassembled and assembled several times?
Some domestic manufacturers in Europe and the United States is the sleeve type pipe joint suppliers, their structure can be repeated disassembly; but some connector is a one-time pressure deformation, the joint group cannot be used repeatedly, or at least need to replace the components outside the card of the pipe, and the sealing surface of the belt assembly still need to check the qualified talents use up a nut by repeating
Q:How many bonding methods are there in the belt joint?
Under normal circumstances, belt joints have mechanical joints, cold sticky joints, heat vulcanizing joints and other commonly used methods.1. mechanical joints, a refers to the use of belt buckle joint, the joint method is convenient and convenient, more economic, if in the process of using belt is damaged, you want to replace the new belt, the belt buckle joint easy to replace, but joint of low efficiency, easy to damage, has a certain effect on the conveyor belt and the service life of the product.
We have qualified engineers for quality control, research and development. If you are interested in our products, please do not hesitate to contact us, we are looking forward to cooperating with you! We sincerely welcome you to come and negotiate with us. Please contact us at any time for more information.

1. Manufacturer Overview

Location Shandong, China (Mainland)
Year Established 2005
Annual Output Value US$5 Million - US$10 Million
Main Markets Southeast Asia
Africa
Mid East
Western Europe
South Asia
Company Certifications ISO 9001 cet ;SGS certificate

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port KELANG,KAOHSIUNG,ALGERIA
Export Percentage 91% - 100%
No.of Employees in Trade Department 3-5 People
Language Spoken: English, Chinese
b)Factory Information  
Factory Size: 3,000-5,000 square meters
No. of Production Lines Above 10
Contract Manufacturing OEM Service Offered Design Service Offered Buyer Label Offered
Product Price Range Low and/or Average