PPR Male Tee Plastic Pipe Fitting Connecting Civil Construction Industrial Agricultural PE Pipes

Ref Price:
$3.50 - 42.00 / pc
Loading Port:
Ningbo
Payment Terms:
TT or LC
Min Order Qty:
3000 pc
Supply Capability:
100000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

PPR Male Tee Plastic Pipe Fittings

Mainly used to connect civil construction, industrial, agricultural and landscape irrigation drainage system PE pipes

 

Main Features of PPR Male Tee Plastic Pipe Fittings

1, health, non-toxic: the various parts of the pipeline system consists of PP-R pipes and fittings constituted can be completely non-toxic, health indicators in line with GB / T17219 standards.
2, does not rust: PH value can withstand a wide temperature range, in the range of 1 to 14, a high concentration of acid and alkali corrosion.
3, wear-resistant, non-fouling: PP-R pipe and tube inner wall smooth, uniform flow resistance is small and does not scale.
4, reducing vibration and noise: PP-R pipe has excellent insulation properties, can significantly reduce the vibration and noise caused by the flow of liquid.
5, anti-cracking: PP-R materials excellent elasticity makes pipes and fittings sectionally With frost expansion of the liquid together without bursting.
6, anti-condensation, heat loss is small: PP-R material is a poor thermal conductor, reduces condensation and reduce heat loss less.
7, anti-electric corrosion: PP-R material is a poor conductor of electricity can avoid corrosion. Complete specifications: 10-30 optional    

 

Pictures of PPR Male Tee Plastic Pipe Fittings

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:PE plastic pipe surface is concave, how could it happen?
Measures should be taken to protect or adjust the connection process under cold weather (--5 degrees below) and strong wind conditions.
Q:The difference between the hot melt connection and connection to electricity
Cost: hot melt than electric melting time: electric melting heat, low melting fast, less than 90 of the diameter of PE pipe can only use electric connection, different manufacturers, different grades and SDR welding pipe fittings, pipes and tubes, pipes and pipe fittings, pipe fittings can only use electric melting connection
Q:What kinds of plastic pipe fittings are there? What are the various uses? And how to distinguish quality?
Pipe fittings are very complicated, preferably with concrete points. As to the water pipe used straight, elbow, three links, three different diameter, different diameter, thread three, straight thread, thread elbow, three links, straight, elbow, as valve, pipe cap, and also have matching specifications and applications;
Q:What kind of flange gasket does the ABS plastic tube work with?
Multipurpose; made of the same material as pipes. Elbow (elbow), flange, three pipe and four pipe (crosshead) and reducer (reducer) etc.. Elbow for pipeline corner; flange for the pipe and pipe interconnected parts, connected to the pipe end, three pipe for three pipe collection; four pipe for four tubes together place; for two pipes of different diameters connected to different diameter pipe.
Q:Regarding the connection of plastic pipes and inspection wells, is the flexible connection or rigid connection?
Connected with the manhole brick or concrete pipe or tube, the intermediate layer is connected with the outer surface approach, part of the advance with polyvinyl chloride adhesive in the pipe or pipe fittings with the wall made of coarse and intermediate layer, and then use the cement mortar wall built into the manhole;
Q:What's the size of the PPR pipe?
When the connection is complete, both the pipe and the pipe must be held tightly and enough cooling time is allowed to cool down to a certain extent before the release of the pipe is continued.
Q:What are the common connecting methods for plastic PP pipes?
Because the hot melt connection method does not need any additional material, and can melt the connection part as a whole, achieves the body strength, the connection effect is good, therefore, here recommends the use of hot melt connection method. The use of hot-melt bonding method should pay attention to the following: first, the hot melt tool to connect the power supply, to the working temperature, the indicator light before the start of operation; II. Cutting the pipe material, you must make the surface perpendicular to the pipe axis. The general use of pipe cutting scissors or pipe cutting machine, using sharp hacksaw when necessary, but after cutting the pipe section should remove burrs; the PP pipe and pipe connection end must be clean, dry and free of grease; the welding elbow or three pass, according to the requirements of design drawings, we should pay attention to its direction in a straight direction pipe and tube, mark the location with the auxiliary mark the connection, no rotation; the end of the guide tube heating sleeve is inserted into the standard depth, at the same time, no rotating the pipe onto the heating head and reached the prescribed mark; the heating time is reached after, immediately put the pipe and pipe fittings from the heating sleeve and the heating head removed simultaneously, quickly and without rotation inserted into the standard depth, making joints form a uniform flange of the joint can be corrected, but not the rotation; to a prescribed cooling time, will The pipe cover is buckled on the pipe fittings.
Q:Can a plastic pipe be evacuated into two vacuum?
Vacuum, of course, but does not guarantee how long the vacuum can be maintained.
Q:As long as the quality of plastic pipe is good Can the problem of plastic pipe connection be neglected?
Only the performance of the pipe itself is not enough, the connection of plastic pipe is the largest local problem in pipeline system, especially the use of pipe connections, such as hot melt connection, no welding operation in accordance with the construction standard, extremely easy to cause hidden troubles due to leakage. General plastic pipe product standards are required to test the applicability of the system, can be selected according to the actual situation of the project inspection. Communicate further if you have any questions.
Q:TTP-PESI hole net steels belt composite pipe fittings need to be taken?
The connection of the hole net, the steel band and the composite plastic pipe can be made by flange connection, and also can be conveniently, quickly and safely welded by sleeve welding. The electric welding is connected with an electric heating element arranged in the pipeline, and the plastic of the inner wall of the pipe sleeve and the outer wall of the pipe (pipe fittings) is melted and cooled after being electrified to generate heat. The joint strength is high, the connecting force of more than 20000 kilograms of pipes and fittings, no leaks and other defects.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range