PP PE Pipe Extrusion Line/ HDPE Plastic Pipe Machine

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
1 set
Supply Capability:
10 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

PP PE Pipe Extrusion Line/ HDPE Plastic Pipe Machine

PE pipe production line is mainly used in the area of agricultural water supply system, architectural water supply system, pavement of cables, etc. This machine group consists mainly of vacuum calibrating tank, haul-off unit, cutting unit, tilter, etc. single screw extruder and haul-off unit have applied imported A/C inverter, both vacuum pump and driving motor have applied excellent products. The haul-off unit includes two-claw type, three-claw type, four-claw type, six-claw type, eight-claw type, ten-claw type, twelve-claw type, etc. Scraps free cutting, saw cutting or planetary cutting can be applied, the property of machine group is reliable, the production efficiency is high. With special device, it can produce inner wall spiral pipe, inner wall hollow pipe, and core layer foamed pipe, etc, it can also produce PP, PE, ABS, PPR, PEX, silicon core pipe and pipe material of other material. The planetary cutting machine is fully automatic computer digital control, it has such advantages of simple operation, reliable property, etc. It has reached world advanced level.

 

Process flow

Raw material + additive → mixing → vacuum feeder → hopper dryer → single screw extruder → marking line extruder → mould and calibrator → vacuum calibration tank → cooling tank → haul off machine → printer → cutting machine → pipe storage shelve

 

Main technical parameter

Model 

PE-16/63

PE-20/110

PE-50/160

PE-75/250

PE-110/315

PE-200/450

PE-315/630

PE-400/800

Pipe diameter 

16-63mm

20-110mm

50-160mm

75-250mm

110-315mm

200-450mm

315-630mm

400-800mm

Max output 

150kg/h

200kg/h

300kg/h

350kg/h

400kg/h

500kg/h

850kg/h

850kg/h

Extrusion speed

1-15m/min

1.2-12m/min

0.6-8m/min

0.5-4m/min

0.4-3.7m/min

0.3-3m/min

0.2-2m/min

0.1-1 m/min

Extruder model

SJ-65/30

SJ-65/33

SJ-75/33

SJ-75/33

SJ-75/33

SJ-90/33

SJ-120/33

SJ-120/33

Installed power

85kw

110kw

125kw

180kw

260kw

325kw

480kw

600kw

Center height

1000mm

1000mm

1000mm

1000mm

1100mm

1100mm

1200mm

1300mm

Line length 

35m

38m

38m

40m

42m

52 m

60m

68m

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What is the principle of the 45 extruder machine?
The principle of the extruder is the theoretical process of heating, melting and mixing in the process of plastic conveying, including solid conveying principle, melt transportation principle, mixing principle, and solid bed crushing process, etc..
Q:Why will the extruder frequency shift stop?
Because the frequency converter is out of order, you can look at the fault record parameters of the inverter.
Q:Cable extrusion machine 6.57090 machine model how to see, know the master to say, thank you
Cable extruder type 657090 machine, describes the diameter of the screw, the unit is mm.The greater the number, the greater the equipment, the greater the amount of gumIt is usually marked on the control cabinet of the equipment
Q:What is the adjustment method of China's extrusion machine die?
(4) lamp alignment: suitable for polythene plastic wires and cables. Use light to illuminate the insulating layer and sheath, observe the upper, lower, left and right sides of the thickness, adjust the screw to the die until it is even, then screw the screws.
Q:Extrusion machine operating procedures, specific points, thank you!
6, the speed from low to high, added to the normal speed, is strictly prohibited high-speed car, observe the instrument on the current value and temperature is normal, in case the current is too large, cause the heater to burn.7, when lifting the disk, we should pay attention to the limit of the rise and fall, not too high or too low, when there is an electrical limit, shall not exceed the limit.8 when feeding to the hopper, be careful not to enter the metal, and do not use a screwdriver or a metal bar to poke the plastic into the screw.9 check the dry test machine, should be equipped with rubber insulation plate, otherwise, no driving.10 before driving, should check whether the ground location is good, grounding resistance should be measured regularly, not higher than 4 Europe; equipment whether there is noise and other anomalies, if there is a problem, repair and reuse.
Q:Equipment is the Changzhou sun extrusion machine,
Is that settled? This technology is not available online! No one wants to say free, need technical contact me!
Q:The working principle of an extruder
The material is moved forward by the extrusion of the screw and the barrel, and the material is fully homogeneous and plasticized in the process of material advance. Then the material is extruded by a certain shape of the die by the die of the die.
Q:What is the waste gas produced by the extruder, granulator and mixer?
Plastic is a chemical product, and the waste gas produced by the process is organic waste gas. The commonly used and relatively efficient treatment method is activated carbon adsorption. The specific work process is as follows: exhaust gas, air pipe, dry filter, activated carbon adsorption, fan and discharge
Q:What are the two types of extrusion?
Extrusion? The extruder. The extruder is divided into single screw extruder and twin screw extruder, and the twin screw extruder is divided into two parts: flat, double and cone.
Q:Floor heating pipe PERT plastic extrusion machine production process,
Is the fitting of the moving parts normal?.Is there an impact on the extrusion chamber?.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range