Power Stacker CL series CL1212 CL1217 CL1226 CL1232 CL1032

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
1 unit
Supply Capability:
1 unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

PRODUCT NAME:Power Stacker CL seriesPRODUCT INTRO

Smooth travel and lift with excellent controls to reduces product damages and increases productivity.
Lift limit switch operates at maximum lift height to shut off pump motor.
A heavy-duty 24-volt electrical system provides good travel and lift speeds.
High quality hydraulic pump assures very little noise, maximum efficiency and durability.
Drive units is equipped with an electromagnetic brake that is spring applied and 
electrically release. Brake is activated by the control handle position. The handle ergonmically 
designed with a raising, lowering and horn bottom.
Speed automatically reduces when driving with the forks at a height of 12" or higher.
Small turn radius makes it suitable for narrow passage ways.
The CURTIS electronic controller helps provide plenty of low end torgue while increasing the motor and battery lift.
Foot pedal reduces fatigue.
Conforms to EN 1726-1 and EN 1175-1
This specification sheet according to VDI regulation 2198 only provides technical values 
for the standard truck. Non-standard types, different masts, additional equipment, etc.
could produce other values. Right reserved for technical changes and improvements.

Residual Capacity at different lifting height

1KG=2.2LB 1INCH=25.4M

Up to h3 mmACTUAL CAPACITY (Q) kg
≤25001200800
≤29001000650
≤3200800500
Load centre distance (C)mm≤600(mm)≤700(mm)

1KG=2.2LB 1INCH=25.4MM

Identification
Model
 CL1212CL1217CL1226CL1232CL1032
Drive:electric(battery or mains),diesel, petrol,fuel gas,manual Electric
Type of operation:hand,pedestrian,
standing,seated, order-picker)
 Pedestrian
Load Capacity /rated loadQ(t)1.21
Load center distanceC mm600
Load distance, centre of drive axle to forkX mm677692
Wheelbasey mm1160
Weightsservice WeightKg750785860885865
Axle loading,laden front/rearKg925/1025940/1045980/1080990/1095885/980
Axle loadings, unladen front/rearKg550/200580/205635/225655/230640/225
Wheels,
Chassis
Tyres:solid rubber,superelastic, pneumatic, polyurethane) polyurethane
Tyre size, front 250x78
Tyre size, rear 80x70 1)
Additional wheels(dimensions) 150x54
Wheels, numberfront/rear(x=driven wheels) 1x+2/4
Track width,frontb10(mm)685
Track width,rearb11(mm)390/515
Basic DimensionsLowered mast heighth1(mm)15652076179520952095
Free lifth2(mm)--144144144
Lift heighth3(mm)11141614251431143114
Extended mast heighth4(mm)15652076298235823582
Height of tiller in drive position min./max.h14(mm)985/1365
Lowered heighth13(mm)86
Overall lengthl1(mm)19081893
Length to face of forksl2(mm)758743
Overall widthb1(mm)805
Fork dimensionss/e/l(mm)60/80/1150
Width over forksb5(mm)570/695
Ground clearance, center of wheelbasem2(mm)26
Aisle width for pallets 1000x1200 crosswaysAst(mm)23402335
Aisle width for pallets 800x1200 lengthwaysAst(mm)23202306
Turning radiusWa(mm)1460
Performance DataTravel Speed, laden/unladenkm/h5.2/5.5
Lift speed, laden/unladenmm/s105/150
Lowering speed, laden/unladenmm/s100/95
Max.gradient performance, laden/unladen%6/12
Service brake Electromagnetic
E-MotorDrive motor rating s2 60minkw1.2
Lift motor rating at s3 15%kw2.2
Battery acc. To DIN, no 3PZS
Battery voltage, norminal capacityV/Ah24/210
OthersType of drive control MOSFET Control
Sound level at driver’s ear acc.to EN12053dB(A)67

Identification
Model
 CL1529CL1529FFLCL1534CL1534FFL
Drive:electric(battery or mains),diesel, petrol,fuel gas,manual Electric
Type of operation:hand,pedestrian,
standing,seated, order-picker)
 Pedestrian
Load Capacity /rated loadQ(t)1.5
Load center distanceC mm600
Load distance, centre of drive axle to forkX mm678
Wheelbasey mm11831168
Weightsservice WeightKg1020104011201140
Axle loading,laden front/rearKg1195/13251205/13351245/13751225/1385
Axle loadings, unladen front/rearKg755/265770/270825/295840/300
Wheels,
Chassis
Tyres:solid rubber,superelastic, pneumatic, polyurethane) polyurethane
Tyre size, front 250x78
Tyre size, rear 80x70 1)
Additional wheels(dimensions) 150x54
Wheels, numberfront/rear(x=driven wheels) 1x+2/4
Track width,frontb10(mm)685
Track width,rearb11(mm)390/515
Basic DimensionsLowered mast heighth1(mm)1950195016951695
Free lifth2(mm)1441472-1104
Lift heighth3(mm)2814281433143314
Extended mast heighth4(mm)3298330339433943
Height of tiller in drive position min./max.h14(mm)985/1365
Lowered heighth13(mm)86
Overall lengthl1(mm)19401925
Length to face of forksl2(mm)790775
Overall widthb1(mm)805
Fork dimensionss/e/l(mm)60/80/1150
Width over forksb5(mm)570/695
Ground clearance, center of wheelbasem2(mm)26
Aisle width for pallets 1000x1200 crosswaysAst(mm)23602345
Aisle width for pallets 800x1200 lengthwaysAst(mm)23402323
Turning radiusWa(mm)14801465
Performance DataTravel Speed, laden/unladenkm/h5.1/5.4
Lift speed, laden/unladenmm/s105/170
Lowering speed, laden/unladenmm/s100/95
Max.gradient performance, laden/unladen%6/12
Service brake Electromagnetic
E-MotorDrive motor rating s2 60minkw1.2
Lift motor rating at s3 15%kw3
Battery acc. To DIN, no 3PZS
Battery voltage, norminal capacityV/Ah24/210
OthersType of drive control MOSFET Control
Sound level at driver’s ear acc.to EN12053dB(A)67

Related Products

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Is there a replacement for similar elevating functions?
Hydraulic system can be used in place of, jack up the operation is convenient, stable, more accurate, simple, a qualified fitter or cold working without much time can make the equipment (can consider to the flea market find some old equipment to assembly).
Q:The tomb raider was not able to pry the gear in order
Press the switch and then descend the elevator down to the second floor and then climb to the right hand side of the cargo and pull down the first gear. Walk to the elevator and climb down the stairs to open the door between the second and third floors. Go up to the third floor and turn the elevator to the third floor. And then you go back to the second floor and you go to the third floor and you go to the sandwich and you get the second gear. Go up to the fourth floor and press the elevator up, go back to the third floor and switch to the three or four floors and twist the third gear. Come down to the entrance of the third floor elevator and then go in and use a shotgun to smash the three floors and the four floors. On the fourth floor elevator again back to the fourth floor, between the back to the fourth floor on the elevator by just open the channel on the wall opposite the detour to the fourth floor mezzanine dropped last gear lever.
Q:Introduction of vertical elevator milling machine
Milling machine is a kind of widely used universal CNC machine tools, can be processed on milling machine plane (horizontal, vertical plane) and groove (key, T slot, dovetail groove, etc.), the points of tooth parts (gear, spline shaft, wheel), helical surface (screw, screw groove) and various kinds of curved surface. In addition, it can also be used for the surface of the rotating body, the inner hole processing and the cutting. Hope to adopt!
Q:How does hydraulic platform change sealing ring, how to operate
Flange join type, should remove flange join screw first, use the screw to remove the end of the cover, can not lever or hammer, lest damage; Inside the card key type connection, should use a special tool, the guide sleeve toward the push, reveal the card key and hydraulic plunger pump used to () after remove the card key items with nylon or rubber texture the card key fill out again after its; Thread connection type oil cylinder, should screw the screw down first; In the demolition of the piston rod and the piston, not hard to pull out of the cylinder, piston rod components should try to keep the components of the piston rod and cylinder axis slowly pulled in a line.
Q:Who can tell me the purpose of the elevator? The more, the better
Single column aluminum alloy elevator: this series of products for indoor type, widely used in star hotel, such as the large supermarket industry lobbies, the aerial work inside the factory, has a balance, convenient operation, can enter the hall, can freely in and out of the elevator and less consumption, no pollution, work does not hurt the earth, can be used for wall and out work, work no dead Angle. The single column aluminum alloy electric elevator is fitted with the gantry cross attachment, which is suitable for the maintenance of movie theater, synagogue and church. The long door is easy to assemble, easy to operate, flexible to move, can span up to 1.1m fixed seat and other obstacles, and can stabilize the work on the step. High strength rectangular steel pipe making, rigid and stable. It is equipped with multi-wheel and flexible. Both ends can be adjusted, which can be used to cross different obstacles. The two sides are vertical adjustable, which can be used for the incline or step of a certain incline.
Q:What is the hydraulic platform driven
The engine or motor drive oil pump can also be used manually.I hope my answer will help you.
Q:How does the platform maintain
Remove and disassemble the valve, and remove the valve core and remove it from the new installation. Put all the hydraulic oil in the tank into the tank, remove the oil absorbent filter, and put it back in the tank. The oil tank refilled with new oil.
Q:What is the imported hydraulic platform car? Kneel and beg your help
Their platform has a special mechanical structure that is widely used in high-altitude work, the shear fork structure, and the higher stability after lifting and lifting
Q:There is no elevator on the 7th floor of the home to install a lift or lift
All manned lift, lifting platform, moreover, to pass through security, common theory suitable equipment can't be through security inspection, after you installed the safety bureau will let you immediately removed. These things are too low
Q:What happens when the platform comes up and the power goes out.
Many platforms have an emergency drop.I hope my answer will help you.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range