Polycrystalline solar panels for rooftop systems

Ref Price:
Loading Port:
China main port
Payment Terms:
Min Order Qty:
26 pc
Supply Capability:
10000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Characteristics of Polycrystalline Solar Panel

I Solar Cell : High efficiency crystalline solar cell. Even if under the weak light, the solar module can produce maximum power output.

II Tempered glass (toughened glass): Anti-reflecting coating and high transmission rate glass increase the power output and mechanical strength of solar module.

III EVA and TPT: Using high quality EVA and TPT to prevent destroying and water.

IV  AI frame: Without screw, corner connection. 6 holes on the frame can be installed easily.

V Junction box: Multi function junction box with water proof.

VI Long lifetime: ≥25 years; Less power decrease.

VII Good performance of preventing from atrocious weather such as wind and hails.

VIII Resisting moisture and etching effectively, not effected by geology. .


Standard Test Conditions of Polycrystalline Solar Panel

The opto-electrical specifications shown below are stabilized values being measured at Standard Test Conditions of multicrystalline silicon Solar Panel, Irradiance: 1000W/m2, Spectrum: AM1.5 at 25°C, The info below is subject to manufacturing tolerances. Where appropriate minutes of measurement are available and are used for the dimensioning of the installation.

Currently,We have 250w-300w solar panel stocks in Both West and East Coasts made in Vietnam,India,Korea,Malaysia and Japan.Meanwhile,we also arrange production line in Wisconsin,USA.If you're interested,please contact us soon.

Thanks for your time.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How do you make a homemade solar panel?
Solar panel cannot be home made with household material. It was a high tech product. You need to buy them in market. To suppose electricity for a trailer home, solar system becomes very expensive . A t least few thousands dollar to buy solar panels, storage battery bank, DC to AC inverter, heavy gauge wiring and hardware.
Q:Maintenance of Solar Panel?
I don't know if the guy is right about cells burning out if they are covered. You should look on the Internet for insolation tables for your area to see the effective hours of sunlight. Then guesstimate the percentage of time the panels will be shaded. Those trees may make the solar thing a poor idea. He is right about the trees reducing you efficiency. If a panel is shaded about 0 percent, its output drops to close to zero. My panels are five years old, and I have washed them twice. There as been no noticeable dropoff in output.
Q:Can a solar panel work with an inverter?
There could be a couple of reasons why it isn't working. First, 2V panels actually put out a considerably higher voltage because it is presumed that they will be used to charge a 2Vdc battery. That requires applying a voltage greater than 2Vdc, and usually there is a solar controller that regulates the solar power to the battery. It also has a voltage drop. Look at the first reference reference, and you will see these values for a particular panel: Voc: 2.6V (open circuit voltage) Vmp: 7.2V (voltage at maximum power point) Voc is the voltage the panel produces under standard sunlight and temperature conditions (25°C), with no load applied. As load is applied, the voltage drops (see reference 2). Power is the product of current times voltage, so at one set of conditions (namely at Vmp) maximum power is available from the panel. Your inverter might not be working for either of two reasons: ) it has input protection circuitry that locks out operation when it senses an overvoltage, as in the 2.6V open circuit voltage, or 2) the panel does not produce enough current and the voltage from the panel collapses under excessive load. For example, if you load your inverter to 20W, then nominally the 2VDC input to the inverter must supply 20W/2V/eff = 0A/eff Assuming the inverter has an efficiency of 80%, the input current required is: 0A/.8 = 2.5A A solar panel operating at maximum power would need a rating of about: 2.5A x 7.2V = 25W Is your panel that big? The other option, as mentioned by others, is to charge a battery that runs the inverter. Other nuances: Voc increases as temperature decreases. Sunlight intensity varies (obviously), so the panel may produce less than rated power. The power specifications often are printed on the back side of the panel.
Q:Solar panel connected to battery ??
You really need a little more infomation about your battery. It should have a recommended range of charging current. You should not exceed that range. Your solar cells must be a higher voltage than the battery, but you should not connect the cells directly to the battery. First, you need a diode in the line to keep the battery from draining into the solar cells when there is no light. Second, you need a resistor to limit the charging current. You have a 3.6v battery. Let's say the charging current is 0.A. Use a 5v solar cell and silicon diode. The diode will drop the cell voltage to 4.3v. The voltage across the resistor will be .7v for .A current, you need a 7-ohm resistor.
Q:Connect Power Outlet to Solar Panel?
Most efficient manner would probably be to use solatubes, or sun tunnels during lighting hours, then replace the 500 watt lighting system (assuming it's incandescent) with LED's, that should give you about the same light output for around 00 watts or a little less even. Then you need a solar panel that can produce 00 watts for as long as you want (at a 00 watt lighting system) or 200 watts for /2 the time you want, etc, etc. Allow a good 0% or so for inverter inefficiencies, and 0% or so for reserve, so 20 watt's per 00 watts. After you have this, you will want a charging controller, a battery, or battery bank (These should at very least be deep-cycle, or better yet golf-cart batteries with series between 2, and parallel between banks of 2 for the 2-volt portion of the system), with enough amp-hours to support your system, plus a good 0% or so reserve, plus another 0% or so for inverter inefficiencies (remember the over sized solar panel above, this is why), than of course you also need a 2-volt DC to 20-volt AC, 60 Hz system (or 240 volt AC 50 Hz system, depending on your AC system) inverter.
Q:what do i have to study to install solar panels?
I want to warn you that very few people will need your service. Solar panels look horrible, and do very little. If it was me and i was interested in greener solutions, i would pursue a degree in environmental engineering. I think that in 0 years time that you will see roofers installing solar panels and your local contractor will be installing personal electric windmills. For this reason i do not believe that there will be much of a future in installing solar panels as a low barrier to entry will mean not much profit or job security.
Q:How solar panels and furnaces work?
Well solar panels conduct electricity from the suns waves and turns it into dc current then it is either put into a grid tie inverter to change it to AC and it makes you meter go backwards instead of forwards. or if its not a grid tie inverter it is just put into batteries as dc then changed into AC from the inverter and then used for household appliances. nothing really does run on DC that is why it has to be changed. and for solar furnaces if you mean a water heater that works by a substance here in Pa its antifreeze is heated up by the sun in the panel it is in a continous loop and that is what gets heated up the water then flows over tow of the tube that contains what ever substance such as antifreeze and heats the water.were the water and the tube that changes the water from cold to hot is called the heat exchanger. the substance is actually get heated first then the water. solar heating for water accounts for 29% of water heating in the us. Now if you mean solar furnace as in passive solar thats completely different because here in Pa if we want it our houses have to face to south to get the suns rays. (alot more windows) and there is a cement slab placed only on the south side of the house and it has insulation covering it. There is a certain type of glass that is used for this that will allow the suns rays to come in and let the heat in for the summer and also for the winter. the main place for that would mostly be the first floor of the house due to the height of the windows and the angle of the sun(pa in the summer is 73 degrees and in the winter its 27 degrees) thats when the second floor would be ok to heat the rooms. Hopefully i helped and i explained it in a way that you can understand.
Q:What is the principle of solar panels to convert solar energy into electricity?
scientists have applied solar cells to space technology - communication satellites. At the end of the last century, in the process of human self-reflection, this clean and direct energy form for photovoltaic power generation has become more cordial, Not only in space applications, in many areas also show their talents. Such as: solar garden lights, solar power generation system, the village power supply independent system, photovoltaic pumps (drinking water or irrigation), communication power, oil pipeline cathodic protection,
Q:Is it worth getting solar panels fitted on my roof?
Homemade okorder.com/
Q:how to chose the right solar panel for my home?
Talk okorder.com has good info. What state are you in?

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range