Pipe Repair Clamp DN32

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Pipe SizeRangeWidth(mm)BoltWorking pressure
Normmminch1bolt2bolt4boltsizeMpa
1/2"21-250.83-0.9875150300M12*1401.6
3/4"26-301.02-1.1875150300M12*1401.6
1"29-331.14-1.375150300M12*1401.6
1"33-371.3-1.4675150300M12*1401.6
1 1/4"42-451.65-1.7775150300M12*1401.6
1 1/4"44-481.73-1.8975150300M12*1401.6
1 1/2"48-511.89-2.0175150300M12*1401.6
1 1/2"50-541.97-2.1375150300M12*1401.6
1 1/2"55-602.17-2.3675150300M12*1401.6
2"60-642.36-2.5275150300M12*1401.6
2"65-692.56-2.7275150300M12*1401.6

material: SS 304,316,304L,316L

The rubber seal can be EPDM or NBR

1.roduct feature :
flexible connection  Firmness and rot- resistance; Need no welding; Without fire danger; Saving space; no limit on a pipe; non-stop plugging, convenient installation
2   application field :
ground surface and underground engineering, Platform for ship building/ marine/ petroleum,water, supplies for coal gas/ natural gas, electric power, industrial production, Wastewater Treatment, and maintenance, etc.
3   Application of pipe line:
crude oil pipeline, coal gas pipeline, natural gas pipeline, Water Supply and Drainage pipeline, fuel pipeline, aviation and automobile only pipeline, lubricating oil pipeline, sludge pipeline, suction pipeline , water flush power pipeline, Cable Protection pipeline, Seawater/Fresh Water pipeline, Turbine pipeline, air conditioning pipeline, fire control pipeline , vent pipe pipeline, compressed air pipeline.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How can the ductile iron pipe be punched?
Ductile iron should be drilled, the key is to see how big holes. If it is a small hole, you can consider using a small drill around 5mm to slowly wear the pipe, and then gradually reaming. If the fight is relatively large hole, may according to the aperture required first hit a circle hole, and then use a small chisel chisel down, slowly put the plate again to be trimmed. When drilling, add a little oil to cool the drill bit.
Q:How many kinds of elbow of ductile iron pipe?
There are 12.5 degrees and 22.5 degrees elbow, but manufacturers rarely produce. You can consult the manufacturer on the Internet
Q:How to inspect ductile iron pipe fittings?
On the quality of single pipe can analyze it from the surface is sand type and water cooled pipes, K8 pipe is different from Shanxi root nature is that the proportion of grade K9 cement and cast iron pipe and the K8 pipe are different, there is no national standard and non standard, no K8 tube, only is the production plant in order to obtain more profits, the dealer is not up to the national standard K9 grade pipe called K8 grade ductile pipe, K9 pipe cement weighs about 1/5 weight of the pipe, but is played in the role of anti-corrosion,
Q:Is the ductile iron pipe metal pipe?
Ductile iron pipes are metal tubes, because ductile iron is also a kind of metal. See the classification of metalsGenerally, metal materials are classified into two major categories: ferrous and non-ferrous metals
Q:How is the weight of nodular cast iron pipe calculated?
In the ferrite and pearlite matrix on the distribution of a certain number of spheroidal graphite, according to the nominal diameter and the elongation of different microstructure of ferrite and pearlite in different proportions of small caliber pearlite percentage is generally not more than 20%, large diameter of the general control in about 25%.
Q:How can ductile iron pipes be connected to steel tubes?
Disk or disk plug connection, it is best to use flange connection.
Q:Comparison of C and K grades of ductile iron pipes
The nominal pressure ratio of the C class pipe is lower than that of the K grade tube, and the applied pressure is low.
Q:What are the categories of ductile iron pipe fittings?
The heat pipe trench is in rotational groove tube internal high temperature composite cold water general PE, cohesive force is very strong and do the destructive test will be found with a knife, the pipe made by hot plastic process, lined with PE layer inside the hard to cut down. The injection pipe is a kind of composite pipe formed by injection of PP into the inner part of the groove pipe.
Q:How can the ductile iron pipe be connected to the PE pipe?
Through the conversion of fittings, because different PE pipes and ductile pipe diameter pipe, so name is needed for the step coupling, called Chinese stepped rod joints
Q:How to improve the quality of nodular cast iron pipe fittings
For cast iron pipe chute taphole bent or improper chute taphole distance socket distance, easy to form a skin defect in cast iron pipe socket parts, equipment manufacturing inspection of cast iron pipe fittings must be in production, replacing the cast iron pipe chute taphole elbow when necessary, and adjust the host making iron centrifuge when the pipe in the lower limit, shorten the chute taphole socket from the distance.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range