The Wraptech Auger Filler is a versatile powder filling machine for dosing free flowing as well as non-free flowing Powders like Talcum Powder, Pesticide Powder, Ground Spices, Ground Coffee, Flours, Milk Powder, etc. The machine operates on the principle of POSITIVE DISPLACEMENT SCREW operating under constant head.
The precisely designed Auger displaces the product through funnel into the pouch/container head under the funnel. The filling cycle is controlled by an Electromagnetic Clutch Brake Unit and Photoelectric Sensor. The machine can be operated in Auto Mode or Manually through a Foot Switch.
10 gms to 1000 gms
Machine Hopper : 35 Litres
1 HP, 3 phase 415 V AC, 50 Hz (single phase drive on request)
1100 mm length, 700 mm width, 1700 mm height
Up to ± 2% for most of the powders, at constant powder level
15 to 25 fills per minute depending upon pack size and mode of packing
Capability to handle wide range of products and pack sizes
Easy changeover for different products and pack sizes
All contact parts are made of S.S. 304
Modular construction assists maintenance and cleanliness
Servo-driven Auger Screw can be provided for better accuracy and speed.
- Q:Ask some books about packing machinery. Especially about carton forming
- Two, with ink printing slotting machine, printing, indentation, cutting angle, slotting, edge separation. Primary molding.Three, the nail box machine or glue will be processed pieces of paper glued to the common carton.Four, ten or several bundles, send away.
- Q:Why should heat treatment be made after glass molding?
- But not so cool to room temperature, due to stress induced crack
- Q:What information does half of the thermoforming wrapper need to provide?
- You need to pack the material, preferably the weight of the material, and if it is powder, how much moisture, good fluidity, also need to provide the size of packing bags, my name
- Q:The film pulling mechanism of the vertical bag forming machine is a little inclined at the left of the synchronous toothed belt pulley
- The bottom belt is inserted into the guide bar. There will be no previous situation. Powder, because the surface is vulcanized, nitrile rubber is not wear-resistant. The effect of silicone on subsequent processing is much better.
- Q:The price of kneeling single station hollow blow molding machine;
- It began to be used in the production of LDPE vials. In the late 50s, with the birth of high-density polyethylene and the development of blow molding machine, blow molding technology has been widely used. Hollow containers can be thousands of liters in volume, and some have been computerized. The plastics suitable for blow molding are polyethylene, polyvinyl chloride, polypropylene, polyester, etc. the hollow containers obtained are widely used as industrial packaging containers.
- Q:What are the plastic forming dies?
- For a combined plastic mold plastic pressure, extrusion, injection, blow molding and low foaming, which mainly comprises a die with variable cavity plastic mold die by the combination of substrate and die components and die combination clamping boards, die with variable core is composed of a convex mold substrate, punch, punch card, component combination cavity blocking assembly and side cutting plate. The coordinated change of die, punch, die and auxiliary forming system. Can be processed in different shapes, different sizes of series of plastic parts. Plastic processing industry and plastic molding machine matching, give plastic products with complete configuration and precise size tools. Because of the plastic varieties and processing methods of various plastic molding machine and plastic product structure is simplified, so the plastic mold of the type and structure is various.With the rapid development of plastic industry and general and engineering plastics in the continuous improvement of the intensity and precision, the application of plastic products is also expanding, the proportion of plastic products is rapidly increasing. A rational design of plastic parts can often replace the more traditional metal pieces of plastic products is also the amount of. Rise.
- Q:How are plastic products formed?
- 5 、 blow molding, blow molding, used in thermoplastics. This is the molten plastic in the mold, under the compressed air pressure, the plastic blow up, close to the mold surface. It is produced by punching and demoulding. It also produces many kinds of hollow packing containers, and also produces films, sheets and so on6. Heating, molding, heating and molding thermoplastic plastics. This is the plastic sheet heating into an elastic state, and then put pressure on the mold attached to the mold. Production of dishware, disc type products.7, foaming molding, foaming molding, the plastic will be added foaming agent, so that foaming, then foam into the mold, curing molding for products. The utility model is used for making cushioning packages for precise instruments and meters.8, molding molding for thermosetting plastics. This is a powder, flake or granular thermosetting resins and additives, placed directly in the mold cavity, the mold closing, heating, pressurizing, plastic and liquefaction, chemical reaction and curing, cooling after the products. Multiple production of sheet and electrical appliances, mechanical parts9, casting molding casting molding for jade. The thermosetting plastic molding powder is placed in the material barrel heating to heat plasticizing, pressed into the mold, and the product complete solidification under pressure. Complex products production needs to block metal objects.10, casting molding for solid thermal plastic. It will plasticized thermosetting plastic injection mould, curing under normal pressure, cooling and demoulding to obtain the products. The production of electronic, electrical and metal insert element.
- Q:What's the maximum size of the automatic packing machine?
- Be sure that the latter machine will be larger. As far as the standard pillow packaging machine is concerned, the largest size of our company is 4380*800*1450mm.
- Q:How to solve the main motor failure of aluminum-plastic packaging machine?
- (3) stuck by a dragging machine;(4) the rotor circuit of the wound motor is opened to break;(5) the head position of the stator is connected wrongly, or there is a break or a short circuit.
- Q:What are the forms of packaging and the forming process of textiles? The more detailed, the better
- How do you do? The packing forms of textiles are coil and neutral packing.Calculation method of forming process:The reed number multiplied by the reed and then divided by 2.54 divided by 2 is equal to the total number of reed teeth. If the average number of reeds is inserted, the total number of teeth is equal to the total number of teeth divided by the number of the total root divided by the number of teeth inserted
Our vertical automatic packing machines are widely used in packing slice, grain, liquid and powder materials such as foodstuff, medicine and chemical products. Equipped with excellent equipment, advance design and assembly line, our company also carries out strict but flexible management system.
1. Manufacturer Overview
||Guangdong, China (Mainland)
|Annual Output Value
||US$2.5 Million - US$5 Million
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||81% - 90%
|No.of Employees in Trade Department
||3,000-5,000 square meters
|No. of Production Lines
||OEM Service Offered
|Product Price Range