PE protective flim HN-80B

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Total Thickness (adhesives + carrier):80+10%micron
Colour: Black & White
Density 0.95g /cm3
Tensile Strength (Long): >18N/25mm
Tensile Strength (Trasv):   >13N/25mm
Adhesion (to stainless steel):150g/25mm
Elongation at break-MD:  >200%
Elogation at break-CD: > 350%  
Static Shear 23 DC: >48 hours
Storage: 35 DC
Humidity: 80%
Shelf: 6 months

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How to easily remove the protective films on ceramic tiles?
Sprinkle some industrial alcohol on the floor and then wipe with a rag three minutes later. It's easy and fast.
Q:What are the differences between PE protective film and PE release film?
PE protective film is used for the primary protection of electronic products when they leave the factory while PE release film is used as disposable consumable to protect the raw materials when wastes is discharged during processing.
Q:How to remove th protective film on the aluminium alloy door which is installed for too long?
Scrubing it using rag with lacquer thinner (diluent).
Q:How to change the screen of mobile phone screen?.
(3) along the direction of the film gently pushing credit card or hard plastic sheet, film direction do gently pushing, the purpose of doing so is to ensure that no film produced in the process of pushing the bubble, while at the same time, while also observed fit part whether there is a bubble, once found on bubbles. Should gently lift, remove dust to continue after the operation, if completely good, then there are bubbles, remedy is not easy.5, completely paste flat, and slowly tear the surface of the second sub membrane. If the model screen is depressed, you can stick it with a strong adhesive glue.
Q:Is it okay not to tear off the protective film on the mirror stainless steel during laser cutting? How about the effect?
The stainless steel must be coated with protective film during laser cutting. And the film must be thick and adhesive enough because air will be produced during laser cutting. If the film is not adhesive enough, it will be easy to be blowed. I suggest you to use adhesive film that is 7C or more thick and 80 degrees or more adhesive.
Q:Does the protective film on the mattress need to be torn off?
Some suggestions for the maintenance of mattresses:1. turn regularly. The new mattress during the first year of purchase, every 2 to 3 months, positive or negative, or around the corner to turn each other, so that the mattress spring force evenly, and then about once every six months can turn.2. keep clean. To do a good job bedding hygiene, sun drying. If the mattress stain, you can use toilet paper or cloth to suck moisture, not washed with water or detergent. Avoid lying in bed after sweating or after sweating, or using electrical appliances or smoking in bed.3., do not often sit on the edge of the bed, bed angle. Because the 4 corners of a mattress is the most fragile, long in the edge of the bed sit, easy to make the edge damage early spring.
Q:How to get off the dust attached to the mobile phone protective film?
It's difficult to remove the dust, I suppose. You can use a bank card to get rid of the bubbles.
Q:What to do if there are some white dots on the protective film coated on high-light product?
Please use protecive film of better quality. The foggy white dots may be generated because the glue reacts with the air.
Q:What are the differences between 360 degrees, 180 degrees and 60 degrees privacy-protective films~
The differences are: the light transmittance of 360 degrees privacy-protective film (about 60%) is lower than that of 180 degrees film (80%). And 360 degrees film protect privacy in all directions but 180 degrees film in only two directions. 60 degrees refer to the visual angel of the computer user, meaning to look at the screen from an angel of 30 degrees from right or left side to the center line of the screen. Please use 3M authentic privacy-protective products.
Q:Fire door finished surface with a layer of protective film is not good to tear
1, it is recommended to tear a corner, in the membrane and the door at the sticky point, pour alcohol, slowly tear.2, or with hot towel hot compress, use the hair dryer blow, also can more easily tear off.3, boiling water method. Suitable for steel, stainless steel, wooden can not use this method.4. Iron with iron. All doors fit.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range