Elevator parts load cell.load sensor
Type EWD-H-J3 Elevator Load Weighing Device
l This system is applicable to all elevators with movable platform car (containing 3-channel programmable switch signals)
l Main characters:
1. Contactless inductive working mode, solid state relay output, no need to fix the original position of elevator overload switch, and to change structure of elevator platform car.
2. Electrical properties is in compliance with the standard of the International Electro-technical Commission.
3. Set up all parameters on the spot.
4. Adopt strong inductive magnet, improve the anti-interference ability to the utmost.
5. System carry scientifical computing out according to mathematical equations to automatically amend detention of error. It also has no-load auto zero capacity
6. It is totally convenient to adjust on the pot by means of artificial self-study or artificial displacement.
7. Control method of programmable output signal created by ourself is applicable to all kinds of traction elevator with movable platform car.
8. Integrated structure design: small size, easy installation.
Scope of application
Applicable to all elevators with movable platform car. range of auto-detention (2.0mm ≤car bottom displacement≤10.00mm ); range of manual set displacement: 2.5~9.9mm ( relate to parameter PD)
Rated load /200 (5.0kg when rated load is 1 ton)
≤1.5% ( 5~40℃ )
Working temperature range≤3.0%
Solid state relay
Programmable universal signal
① 3 channel programmable output mode are following: no- load, light- load, semi-load, heavy load, rated load and overload (user can freely set up the range of change.
② Each channel can be programmed as dynamic close or dynamic break contact.
③ Contact capacity: DC/AC 32V/15mA
Elevator load "no load~rated load", analog quantity:0~10Vlinearly changing
movable platform car of elevator
Referring to diagram, by means of Holzer sensor this system tests displacement changing based on platform car of elevator and load elastic variation principle. It use single chip microcomputer to scientifically compute to correct error in terms of given parameter and measuring results based on mathematic equations, which accomplish effective load weighing of the elevator platform car.
l EWD-H-SJ3 TESTING LOAD OF INDUCTIVE ELEVATOR
Appearance & interior structure
Other weighing devices
Adopting Holzer sensor. Accomplishing contactless inductive working.
① Has long working life in that this system don't bear load of elevator.
② Width induction & high positioning precision.
③ No system damage arising from insufficient overload capacity and mechanical vibration.
④ Micro sensor & microcomputer make system highly intelligent and lower power waste.
⑤ Automatically amending detection error by means of digital. Good linearity.
Directly bear elevator load by the way of pressure sensor.
Only need to fasten the device in the middle of bottom of platform car or original position of mechanical switch in the condition of failure to change structure of platform car. Small size & Easy installation.
Need to change structure of the platform car. Uneasy to install & more work.
Adjusting on the pot
① Thanks to the high intelligence personnel may complete adjustment of elevator weighing device on the spot after separately press the button of sensor two times following the completion of installation system sensor when elevator is no load or rated load.
② Elevator producer may directly complete quick adjustment of similar elevator by the way of setting-up the manual displacement.
Advantages: easy & quick to adjust
Complicated adjustment owing to the analog signal.
Connecting the interface of output signal on the select layer device
3-channel programmable output terminal could be set up by user themselves. Selection: no load, light load, semi-load, heavy load, rated load, overload; 0~10V analog output. It is convenient for user to finalize the items below: 1 vandal resistant function. 2 full bypass function. 3 energy saving function. 4 debugging system torque compensation.
① High-performance to price ratio, easy to use, low breakdown.
② Less accessories, low additional cost & simple processing
High additional cost
Any information needed, please ask for the operation manual from us.
- Q:A workshop needs to be packed with machine parts. 5 boxes are packed in 80
- 5 boxes, 80 boxes, =16 20 boxes, only 320 can not be loaded
- Q:What is the definition of machining process specification?
- The machining process is the process of manufacturing or processing parts or parts, using the method of machining
- Q:The true size of a mechanical part is based on what is on the drawing
- The most accurate size is dimensioning! You can't draw correctly, but as long as the marking is correct, the processing is in accordance with the dimensioning!
- Q:How to package machined parts?
- If it's not rusted, clean it and wrap it in a bubble bag. Place it in a cardboard box or wooden case
- Q:What are the main parts of small vacuum machines?
- On the vacuum chamber, opening displacement and balancing deviceThe commonly used vacuum machine has a single room and double room two, single room for tipping, two stents in the upper and lower vacuum chamber with a middle rear, wearing a double torsion spring axis by double torsion spring force balance, the opening angle of 45-75 degrees ranging. Double chamber for reciprocating, vacuum chamber is divided into two studios, vacuum chamber comprises four connecting rod support about displacement, the four connecting rods is fixed on the two axis, the long axis of a spring fork, two tension springs located in the lower frame, the upper part of the positioning in the spring fork, to balance the operation of gravity, two axis by two sets of bearing positioning, four upper connecting rods with miniature bearings, so the displacement is very easy, starting with vacuum pressure, back after gas can automatically open. The four connecting rods on the support displacement of the vacuum chamber, before and after each axis on the two, must be kept parallel to about two sets of connecting rods must remain relatively parallel, to ensure that the vacuum chamber remain parallel in about any position under the same vacuum chamber or cause the upper and lower vacuum chamber can't keep parallel, then the operation pressure increased significantly, even can not establish normal vacuum. Small treasure vacuum machine
- Q:What's the price difference between feed packer and organic fertilizer packing machine?
- Organic fertilizer packaging machine and feed packaging machine is still the main difference between, in the mechanical structure, equipment selection, components and so on
- Q:What is the principle of cleaning machine parts? How should the parts be kept after cleaning?
- Cleaning of precision parts usually requires special cleaning agents. Canned high pressure sprays are expensive, but the cleaning effect is very good, volatile, and parts will not rust. Ordinary cleaning parts can be washed with water, but must add parts cleaning agent (bags, a bit like a soap, but wet, low price) to prevent rust, cleaning after drying can be, if there is a high pressure air drying is better, but this kind of cleaning agent is injured hand, should wear gloves when cleaning.
- Q:Single vacuum packaging machine accessories, vacuum schedule, where to sell?
- Hello, I Division specializing in the production of vacuum packaging machine, vacuum packaging machine accessories, good quality and low price
- Q:Functional configuration of plastic processing machinery
- After 80s, China's injection molding machine industry developed rapidly, with an annual growth rate of more than 20%, and gradually formed a processing base mainly in Zhejiang, Ningbo, Guangdong, Dongguan and Shunde. Among them, Ningbo injection molding machine production and sales accounted for more than 60% of the total production and sales. In 2002, the production and sales volume of the whole machine has reached 30000 units. In 2003, it was estimated to reach 35000 units, accounting for about 60% of the total annual output of China's mainland and about 30% of the world's total output. Ningbo is only one city, there is the size of the injection molding machine production enterprise more than 100, including the world's first production and sales of the China Haitian Machinery Co. Ltd. and more than 10 foreign-funded enterprises, involving companies more than hundreds of.China's large backbone injection molding machine manufacturing enterprises are mostly joint ventures, introducing foreign advanced technology and management mode. In terms of technology, the injection molding machines produced in China have been developed from ordinary models to large machines, electronic machines, oil and electric machines and special injection molding machines. Among them, the Haitian developed China's largest clamping force injection molding machine, used in the production of auto parts; Zhen Xiong developed a full electric disk machine for the production of special machines and PET bottles for injection molding special models. Although on the whole, the injection molding machine Chinese production is mainly low-end products, but to the Haitian injection molding machine manufacturing enterprises and Zhenxiong as the representative of the effort to end market development.
- Q:What kind of material is better for food packing box?
- Breaker shell, switch, motor, fan shell instrument machinery parts, currency-counting machine parts, electric irons, electromagnetic stove oven accessories; automobile industry in the flow control valve, carburetor cover, window controller, pedal transmission, switchboard cover; mechanical industrial gear, vane, pulley, pump parts, in addition to a wheelchair car body and wheels, lamp shell, lighting device shell, drainage pipe joints, zipper, watch parts, spray parts.
1. Manufacturer Overview
|Annual Output Value
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
|No. of Production Lines
|Product Price Range