Pallet Tilter LT series

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
1 unit
Supply Capability:
1 unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

PRODUCT NAME:Pallet Tilter LT seriesPRODUCT INTRO

Manual and Electric Version

Designed to give the user an ergonomically correct position to reach loads easily without the    necessity of bending down or stretching up.
Handle can be turned and locked in position away from the work area.
Applies to both sitting and standing positions.
Forks can be tilted up to 90.
Both are supplied as standard with parking brake and foot protectors.
Conforms to EN1757-1 and EN1175.


1kg=2.2lb1ICH=25.4MM

 
ModelLT10MLT10E

Type

ManualElectric

Capacity

(kg)10001000

Lifting Height,Vertical

h(mm)285285

Min.Fork Height

h1(mm)8585

Fork Length

l(mm)800800

Handle Height

L1(mm)11381138

Overall Fork Width

b(mm)560560

Width Between Forks

b1(mm)234234

Fork Tip Length From Roller

L2(mm)135135

Overall Width

B(mm)638638

Overall Length

L(mm)13251410

Overall Height,Raised

H(mm)950950

Overall Height,Lowered

H(mm)750750

Load Centre Min./Max.

C1(mm)200/400200/400

Load Centre Min./Max.

C2(mm)200/420200/420

Power Unit

(KW/V)0.8/12

Net Weight

(kg)178185

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How is the lifting handle of the universal knee-milling machine very tight
You're talking about a tight lock or a handle.I hope my answer will help you.
Q:The tomb raider was not able to pry the gear in order
When I play this card for a long time, also I am getting rid of the four is only the past, the front three gear easy to find, the fourth in 3, 4 layer between the right of the lift, there is a hole, was blocked by a few boards, you can go out from there the fourth also make it
Q:How to maintain the platform?
My company has, our brand: niu power Throughout guangdong, there are 57 dealers across the country. Check it online, it's ok to buy it, but at least it will give you advice and contrast!
Q:What is the difference between elevator and elevator
It's the same, but everyone's understanding is different.I hope my answer will help you.
Q:Diablo ii flame volcanic mission will not be able to jump
Push the pole to the right to climb quickly to seize the board on the wall, press the left key to left, after the magma press e and ran to the front of the counter, jumped to the table according to move to the left along the plate on the plate
Q:How to use the ball screw platform?
Second, heyman screw can see lu, platform settled on first use, carefully to see if there are any more abnormal hydraulic parts, electrical appliances, layout, to ensure that no more than about geomagnetic held before commissioning, no-load again after 3 ~ 5 times a load test.
Q:What about the heat treatment of the lifting platform?
Ball screw work is often subjected to bending, torsion, fatigue and shock, while also bearing friction on sliding and rotating parts. The damage form of ball screw is mainly worn and tired. Therefore, its performance requirements as a whole must have good comprehensive mechanical properties (that is, a certain amount of strength and toughness) and high dimensional stability, working parts (raceway, diameter of axle) requires a high hardness, high strength and wear resistance. You are recommended to go to hymanu
Q:There are several reasons for the hydraulic cylinder oil leak on the elevator
Internal leakage 1) wear-resisting ring on the piston is badly worn, causing friction between the piston and the cylinder liner, and finally pulling the casing, piston and seal. Sealing long term failure, piston seal (mostly U, V, Y ring, etc.) aging; 3) the hydraulic oil is dirty, and a large amount of impurities enter the cylinder to seal the piston seal to the bad.
Q:Does the shear fork lift stand belong to special equipment?
It belongs to special equipment, the manufacturer must have special equipment production qualification "special equipment manufacturing license" to be able to produce the sale shear fork lift machine. The products of the manufacturer without relevant documents are not eligible.
Q:What is the imported hydraulic platform car? Kneel and beg your help
Wide operating platform and high load-carrying capacity, make high-altitude operation more widely available, and suitable for many simultaneous operation. You can ask.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range