new malleable iron pipe clamp fittings

Ref Price:
$0.03 / pc
Loading Port:
Payment Terms:
Min Order Qty:
100 pcs pc
Supply Capability:
300000pcs Per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Usage: Pipe Clamp
Material: steel、matel;Galvanized iron ,stainles
Band width:3mm/20mm
Model number:As your requirement
Structure:Swivel clamp
1.Use the open internal and external circle structure,and with screw fixed.It is effectively to solve the problem that when small diameter solft tube connect the hared tube,it is easy appear dead angle,and liquid or gas leakage problem.Easy structure,Easy maked.
2.Edge is no burrfree,it is ability to prevent the tube damaged
3.By a efficiently hydrogen relief treatment,long-term use needn't to worry fracture and other problems
Surface: zinc plated Packaging
4.Accord with DIN3017 Standard.By 48 hours salt and fog test,it has a good corrosion resistance
5.By our last 48 hours elastic test,to insure a high strength mechanical properties.
6.Easy to fix.
Working Temp: -40 ℃ ~ 110 ℃
Size:3/8" 1/2" 3/4" 1" 1 1/4" 1 1/2" 2" 2 1/2
Structure: Suspension Clamp and so on On-time shipment and pre-shipment product quality safeguards clamp is mainly used in automobiles,tractors, ships, gasoline engine, and so on each kind of mechanical
device for oil, gas, hydraulic hose connector, various types of
rubber tube interface must join parts fastening.
Detail: plywood case ,pallets or any other package as buyer's requirements
Delivery Detail: about 20-30days

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Generator carbon brush fire how to deal with?
Generator is DC or AC, DC generator carbon brush ignition, then the coil is short circuit, to find a short separation, just fine! AC generator carbon brush ignition, then the carbon brush is not good to change it, there may be carbon brush in front of the copper ring is too dirty, with sandpaper sand just fine.
Q:The multimeter, megohmmeters and use clamp meter.
Preparation prior to use1, check whether the European watch can work properly, place the watch horizontally, and empty the handle of the euro watch. The pointer should point to. O, and then slowly shake the handle, so that L and E two terminal pile output line instantaneous short, the pointer should quickly point to zero. Note that the L and E cannot be shorted too long when shaking the handle, otherwise it will damage the watch. ,2, check the electrical equipment and circuit being tested to see if all the power has been cut off. Never allow equipment and lines to be charged with a European watch.3, before measuring, deal with equipment and line the first discharge capacitor discharge equipment or line so as not to endanger the personal safety and damage megohmmeters, it can reduce the measurement error at the same time, attention will be the test point to wipe clean.
Q:How to measure the static grounding resistance
The grounding resistance tester model is ZC29B. There are three lines: 20 meters of ground pile and 40 meter stake respectively
Q:How to use the pliers?
Clamp meter is to measure the AC current meter, only AC can be used, when using single line wire clamp, clamp meter in the middle, according to the size of the current regulation of the current size of the gear, you can read the current readings.
Q:The reason that the phase current meter of the three-phase asynchronous motor is too low and the other two phases is normal is that it is too normal
If it is a new repair motor, and the three-phase voltage balance is the current is too low, there is a problem with the phase turns and wire diameter, two is the current meter and transformer problems.
Q:The power consumption of the same load, different power motors?
When the 380V/55KW motor is full, the current is 100A. You only have 70A now, which means that your load is only about 35KW37KW motor can be used instead of the current slightly less than 70A, but not much. Nothing changed, slightly less. Idle work will be much smaller.
Q:Is the flow meter good or the multimeter?
The multimeter is divided into a pointer multimeter and a digital multimeter according to the display mode. Is a multifunctional measuring instrument, multi range, general multimeter can measure DC current, DC voltage, AC current, AC voltage, resistance and audio level, some parameters can also be measured AC current, capacitance, inductance and semiconductor (such as beta) etc..
Q:Is there a caliper meter that can measure direct current?
Magnetic balance type current sensor called compensation sensor, namely the primary current Ip generated in the magnetic core premises through a secondary magnetic field coil current magnetic field generated by the compensation, the compensation current of Is accurately reflect the current of primary side Ip, so that the Holzer device is in the working state of zero magnetic flux detection.
Q:How much power does a computer power 297W require?
Look at the power 12V output, 12V output over 300W, you can take.... that is more than 350w.If you think power 300W, you can use 300W band, that is pure white
Q:DC current detection method
Small power DC current is usually measured by a multimeter in series. The circuit can be measured by a DC clamp type or a DC shunt. But the DC shunt must be used in conjunction with the DC ammeter, usually fixed.

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range