Q:I am trying to replace my kitchen faucet and that plastic nuts/fasteners are screwed on too tight. I can turn by hand or adjustable wrench. There is very little room to work with when trying to use wrench/plyers.

visit the ironmongery shop and purchase a plumbers wrench. that's a wierd looking subject that sounds like it's going to under no circumstances paintings. expenditures around $12.00. The ironmongery shop can clarify the way it quite works. in case you could unscrew the nuts adequate to advance the fixture up yet no longer get it off, you could take a observed-ZALL or a hack observed blade. and decrease off something from on acceptable (between the fixture & the sink). Becarefull to no longer scratch the sink with the observed blade. attempt putting some duct tape the place the blade would are available touch with the sink. once you put in the hot fixture, coat the threads with a lithium form grease, that protects the threads from rusting and could be greater convenient to change next time.

Q:I would like to give a sink and faucet the appearance of having plumbing for display purposes. Is it possible to use a fountain mechanism to create that effect. I'd like to be able to turn a handle and have the water flow, then drain back down into a basin to be pumped through continuously if left on. but able to be shut off by simply turning the handle back to the off position.

It may be less expensive to buy a 12vdc RV pump but then you'll need a car battery or 120vac/12vdc converter. Won't hurt to check w/the pump mfg to insure your no flow (valve closed) time won't hurt the pump. Install a filter on the pump suction line and you should be good to go...

Q:Kitchen basin basin faucet down how to repair

Look at the leading buds and nuts have broken off? Not broken is the faucet and the bottom of the basin at the bottom of the faucet nut tightened just fine

Q:How does the faucet of the faucet on the basin disassemble?

With the pliers to clamp the leading water into the water pipe iron counterclockwise turn can be removed (may be a little scale to force point)

Q:What is the price of the basin faucet?

I think it is necessary to refer to the price of your basin, have to match it! Market price too much water.

Q:How do I remove my old kitchen faucet?

There are different styles of faucet. There may be one projection or three (or four.) You would have to go back a very long way for the thing to be screwed down from the top. Usually there is from one to four "nuts" that hold the faucet down to the sink top. You are going to have to crawl under the sink to see and loosen them. It is an good place to start anyway as you are going to have to see if you can turn the water off under the sink or have to turn the house off instead. Once the water is turned off, disconnect the supply tubes and then loosen the nuts and remove the faucet from above. Most of the modern nuts are plastic but older ones may be rusted and difficult to remove. Sometimes a basin wrench can help and at least once I had to cut the faucet off with a sawzaw after removing the countertop.

Q:how necessary is a reservoir wrench when installing a new faucet?

Since there is no such thing, not very important at all. If you mean a basin wrench (such as what is in the provided link), though not *necessary* it can (in some circumstances) make installation much easier. Al

Q:7 1/2 deep SS sink with Delta, single hole with spray fauct.white Kohler basin and toilet.also available - 36 white vinyl base cabinet for sink.

All the answers here are funny. Since it happens when you flush the toilet or use the sink, I as a amature plumber would suggest that you have a venting problem. What is happening is when you use a drain you need air to help the water go down. When you don't get the air, the water is sucked out of the trap and you smell the sewer gases. The trap is the U shaped pipe under your sink. It is built into your toilet. If you have a vent pipe coming out of you roof. (I really hope you do) it may be clogged with leaves, dead birds, bugs or other junk. Fix..get a snake and push it into the vent pipe from the roof down. In case you don't know....a snake is a coil of flexable steel used ny plumbers to clear clogged sewer pipes and vents. As for the worms in your water pipe, quit watch those horror movies and leave them drugd alone.

Q:Hi, I recently replaced a washer on my hot water faucet and now when running the hot and cold water to shower etc. both run for a bit of time and then I hear a thunk noise (loud enough to hear above the noise of water running) and the hot water will drop off as if it is turned off. I then turn on more and the water runs with no problem. This is constant every time I use it. Any ideas. I believe my cold water slows down also but cannot be sure. I have two handle faucet with a pull up button (for shower) on spout. Sometimes the water after turning it up will come out of the faucet head alittle as if the water is pushing out where ever it can. Thank you for any help you can give me.

a rubber washer can warm up with hot water and swell which shuts the water off. That usually means you have the wrong washer in there. since u already threw the old one away lots of luck.

Q:Bought a bathroom counter basin combination. Ready to buy their own lead, suddenly found the leader has a radius of a said. What the European standard GB. , Whether it can only be used

Actually is the interface caliber