Mylar Lamination Film- 50mm Width Metalized PET/Polyethylene
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 10000 m²
- Supply Capability:
- 1000000 m²/month
- Option:
- 1.2m*3000m
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Item specifice
Product Structure
Widely used for laminating with EPE insulation, Bubble insulation, woven fabric insulation, etc
● Aluminum foil – LDPE
● Aluminum foil- PET- LDPE
● Clear Transparent PET-Aluminum foil – LDPE
● Aluminum foil-Metallized PET- LDPE
● Metallized PET- LDPE
Product Application
Widely used for laminating with EPE insulation, Bubble insulation, woven fabric insulation, etc
Product Advantage
Light weight
• High manufacturing accuracy
• High strength
• Small inertia resistance
• Strong heat dissipation ability
• Good visual effect
• High reflective insulation
• Heat resistant, water proof, stable at high temperature;
• Environmentally friendly, no smell and not-toxic;
• Smooth and clear surface;
Product Packing
1. Waterproof paper then PVC shrinking Film
2. Kraft paper only
3. Woven cloth
4. Kraft paper or Water Proof Film then Metal/wooden pallet
5. (Also as your request. )
Product Remarks
1. The data above are typical results and subject to change without notice.
2. Tolerance: Weight and Thickness: ±10%; Width: ±3mm;
Length: Cut Roll & Log Roll ±0.3m, Jumbo Roll ±0.5%.
3. The products should be stored at room temperature and kept from wet and heat source.
4. It is essential, as with all pressure-sensitive tapes, that the surface to which the tape is applied must be clean, dry, and free of grease and oil.
5. The user should take test and do trial-application on the above products before coming into application so as to witness and ensure suitability for user’s special purpose and technique.
Product Data Sheet
PROPERTIES | UNIT | VALUE | TEST METHOD |
Basic weight | gsm | 33.5 | ASTM D646 |
Thickness | mic | 23.2 | ASTM D646 |
Tensile strength: M. D. X. D. | N/15mm | 13.5 13.5 | ASTM D882 |
Delaminating Values | N/15mm | 1.5 | ASTM D904 |
Reflectivity of foil surface | % | 95 | ---------- |
Temp. Resistance | -40°C 130°C | No Delamination No Delamination | ASTM C1263 |
Water vapor permanence | ng/N.s | 1.15 | ASTM E-96 |
Product Picture
FAQ
1. What is the product keeping conditions?
The Aluminum Foil Facing should be stored at room temperature and kept from wet and heat source.
2. What is the guarantee years of the products？
We have established the international advanced quality management system，every link from raw material to final product we have strict quality test；We resolutely put an end to unqualified products flowing into the market. At the same time, we will provide necessary follow-up service assurance.
3. What is the delivery time of the order?
In the purchase of product within four working days, we will arrange the factory delivery as soon as possible. The specific time of receiving is related to the state and position of customers. Commonly 7 to 10 working days can be served.
- Q:Do you want to remove the wrapping plastic film from the new mattress?
- Restoring the inherent elasticity and comfort of the mattress. There is a bed on the mattress. The sheets are very sanitary. It is not necessary to keep the plastic film in it.
- Q:Should the film on both sides and back of SIEMENS refrigerator be torn off?
- This requires the iron sheet outside there is no shelter, otherwise it will affect the cooling of the condenser, resulting in increased power consumption. So, remove the film from both sides of the refrigerator and the back.
- Q:Why use plastic film wrapped legs running, weight loss good?
- Wearing a heavy sport suit or body sculpting exercise also temporarily reduces weight, and restores weight as soon as you add water." The best way to lose weight is for a small amount of exercise, a long period of exercise, while focusing on the requirements of a balanced diet. The general principle is that the exercise center rate is 120 times per minute, the duration of exercise lasts more than 45 minutes, the next day or every day, and attention to the diversity of sports events.
- Q:Why should farmers cover plastic film when sowing in the spring?
- Reduce the damage of weeds and aphidsMulch can inhibit weed growth. In general, the coverage of weeds covered by mulch is reduced by more than 1/3. If combined with herbicides, the effect of weed control is more obvious. After spraying herbicide, plastic film and film covering weeds can reduce 89.4~94.8%. The film has a reflective effect, and can partly avoid aphids, inhibit the propagation of aphids, and reduce the spread of hazards and diseases.
- Q:Such equipment is used for cutting paper?
- Finally, with a sharp knife along the fiber plate width on one side of the film will extend into the open, sealing is formed of plastic bags. We used to make plastic bags like this.The fiberboard is about 3-4 millimeters thick and can be replaced with other sheets.
- Q:How can the weathering of the plastic film on the surface of FRP be removed?
- Solvent treatment. The use of solvent dissolution to deal with, clear plastic film surface of the organic dirt, dissolved and swollen plastic film surface, to improve adhesion to the ink. Because this method is more polluting to the environment, and the surface of some plastic film will corrode and cause cracking, so it has not been used except for the laboratory.
- Q:Glued to the door, how can the plastic film be cleaned due to oxidation?
- 1, if the area is not very large, you can use a proper amount of banana water soaked, and then use clean cloth can be wiped.2. Try cleaning with textile detergent.
- Q:Can the concrete be covered with plastic film in summer?
- Plastic film is required.Concrete, can gradually hardening is mainly because of the effect of water cement hydration, and requires proper temperature and humidity conditions, so in order to ensure the concrete has hardened the proper conditions, the growing intensity must be maintenance of concrete. Covering curing is the most common method of keeping warm and maintaining moisture.
- Q:Why should antistatic treatment be applied to plastic film printing? What are the treatment methods?
- Film printing, bag making, packaging. In the storage, storage process, with electrostatic, will make the bag surface adsorption of dust in the air. Therefore, plastic packaging, printing materials, antistatic treatment must be carried out
- Q:What is the best plastic welding method?
- It must be welding with ultrasonic wave! Because he doesn't need other additives, and the efficiency and welding effects are not artificial. Unless you're a big plastic product.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
Mylar Lamination Film- 50mm Width Metalized PET/Polyethylene
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 10000 m²
- Supply Capability:
- 1000000 m²/month
- Option:
- 1.2m*3000m
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords
