Monocrystalline Solar Module 265W

Ref Price:
Loading Port:
China Main Port
Payment Terms:
Min Order Qty:
Supply Capability:

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Solar Monocrystalline (210W-225W)

Introduction of Solar Monocrystalline (210W-225W)

Solar modules use light energy (photons) from the sun to generate electricity through the photovoltaic effect. The majority of modules use wafer-based crystalline silicon cells or thin-film cells based on cadmium telluride or silicon. The structural (load carrying) member of a module can either be the top layer or the back layer. Cells must also be protected from mechanical damage and moisture. Most solar modules are rigid, but semi-flexible ones are available, based on thin-film cells. These early solar modules were first used in space in 1958.

CNBM Solar photovoltaic (PV) Panel is designed for large electrical power requirements. It is the optimal choice for both on-grid and off-grid power systems. CNBM Solar panel offers high performance of power per square foot of solar array. Monocrystalline silicon(c-Si): often made using the Czochralski process. Single-crystal wafer cells tend to be expensive, and because they are cut from cylindrical ingots, do not completely cover a square solar cell module without a substantial waste of refined silicon. Hence most c-Si panels have uncovered gaps at the four corners of the cells.

Characteristics of Solar Monocrystalline (210W-225W)

I. Solar Cell : High efficiency crystalline solar cell. Even if under the weak light, the solar module can produce maximum power output.

II. Tempered glass (toughened glass): Anti-reflecting coating and high transmission rate glass increase the power output and mechanical strength of solar module.

III. EVA and TPT: Using high quality EVA and TPT to prevent destroying and water.

IV. AI frame: Without screw, corner connection. 6 holes on the frame can be installed easily.

V. Junction box: Multi function junction box with water proof.

VI. Long lifetime: ≥25 years; Less power decrease.

VII. Good performance of preventing from atrocious weather such as wind and hails.

VIII. Resisting moisture and etching effectively, not effected by geology.

IX. The certificate issued by international authority: UL, TUV, IEC, VDE, CE.

Standard Test Conditions of Solar Monocrystalline (210W-225W)

The opto-electrical specifications shown below are stabilized values being measured at Standard Test Conditions, Irradiance: 1000W/m2, Spectrum: AM1.5 at 25°C, The info below is subject to manufacturing tolerances. Where appropriate minutes of measurement are available and are used for the dimensioning of the installation.

Advantages of Solar Monocrystalline (210W-225W)

• CNBM Solar performance guarantees for 25 years

• 10 years guarantee for workmanship

• Timeliness of delivery

• Quality Products certified (TÜV, UL, CE, VDE, ISO)

CNBM International Corporation's products including Monocrystalline Solar Panel, Polycrystalline Solar Panel have received and enjoyed famous reputation in many countries and regions in the world .As a solar panel manufacturer in China, we strive to provide our customers with excellent service, superior products and unmatched value.  

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How effective are solar panels now in N E with our 40+ snowfall this month?
Green energy magically makes the snow transparent. The more I learn about solar and wind, particularly selling excess power back to the utility, the less sense it makes. You'll have noticed, perhaps, that there was no way to store the power from the panels for when it's really needed.
Q:Question about Solar Power and Wind Power?
A 000 sq. foot abode isn't very great whilst it includes the standard length abode. at present the main inexpensive and best variety of eco-friendly potential for powering a house is wind potential. an outstanding wind turbine can get you on the brink of seventy 5% to a hundred% or much extra performance. extra beneficial potential produced via wind will reason the electrical powered meter to run backwards. At that factor, you're promoting the surplus electrical energy decrease back to the electrical powered company, providing you with extra money in the direction of a destiny electric bill. in spite of if image voltaic potential can help, image voltaic potential, in itself, might fee 2 to 5 cases extra beneficial than wind potential.
Q:How do you use solar panels?
Custom solar-heating systems are unique. Does yours have a circulating pump? Does it have a storage tank? Is the fluid that goes to the panels separated from the household water and transfers heat through a heat-exchanger radiator, and the fluid has antifreeze in it? If it does, is the antifreeze of the variety that won't poison your family if there is a leak? Does your system have a thermostat-controlled pump that turns on when the water in the panels are hot? Does it have a limit-thermostat to turn off the pump when water in the storage tank is hot? There are many more variations to operation of solar-heating panels. Find out who designed it or who knows how to operate it and ask them.
Q:Blocking diode for solar panel?
At least a 2 amp diode. rated above the 2 volts that are commonly found on the market. A blocking diode must be able to stop a higher current and voltage than the panel maximum. A diode will work on any voltage and current lower than it rating.
Q:Air conditioner 25 volt 5 amps: how many solar panels and batteries to run 24/7?
Unless you have a good charge controller, the battery will never charge, as a lead acid battery requires 5 volts to charge. Ans you don't tell us the capacity of the battery? Is the solar cell only 5 watts? That is amp if it develops 5 volts. Assuming the solar panel is good for 5 watts and 5 volts, that is only amp. so you are charging the battery with amp and discharging it with 5 amps, so how long you can do that depends on the size of the battery. But it will discharge in at most 5 hours with a large battery, and the solar panel will take several days to charge it up again at amp. The best you will be able to do with that 5 amp load is perhaps hour a day, which is 2 watt-hours. The solar panel will be able put back amp for 2 hours at 5 volts, which is 5 watt-hours, which will give you perhaps 2 watt-hours in the battery. .
Q:Can A Home Owned Solar Panel Support The Entire House's Electrical Needs?
Q:Is it truE thet solar panels. . ?
Q:Making a Charger out of small solar panels?
3-T is just one type of many devices designed to control voltage so you get the amount you desire with as little static as possible. Without you having an degree in engineering, I can't explain it to you any better. You will also need to produce true sine wave energy or you will burn out your PSP with the correct volts and amps. You need one to produce only 5 volts 2amps. Anything different will burn out yur PSP. Your problem is simple math. Watts = volts multiplied by amps. Amps = Watts divided by volts. So if your solar panels can produce /4 amp ( 250 mA) each, then you connect one to the other in a series until you get enough connected to make 2A. ( 8 panels { /4mA x 8 = 2A}) You now have a panel with 32Volts, 2Amps, 64 Watts. This is where the T-3 regulator comes in. If you buy one for 5 volts, it will allow only 5 volts 2 amps, to go to your PSP.
Q:Pls is it ok to connect a 0watt and 20watt solar panel together into a charge controller port?
Tobi, generally yes, solar panels are like beer, all the europeans get along fine, you can put two Belgiums in the same room as one German and three Englishman. As long as the panels have roughly the same open circuit voltage, usually around 8 volts, then go for it. If you're not sure about this, or the panels voltage disagrees dramatically, then they can still work through the same charge controller, the only other thing you need is a bypass diode in the junction box on the back of each panel. Most modern panels come with these already installed. They are simply electrical check valves, allowing current flow in one direction but not the other. The reason these matter is when the sun is first coming up, the higher voltage panel can force its power backwards through the lower voltage panel, at least until they both reach a voltage higher than the charge controller is set at. This is not a desirable thing to have happen, the 20 watt panel, if its voltage is higher, can damage the 0 watt panel without these diodes if the 20 watt has a much higher open circuit voltage, or Vmax. Look on the back of the panel for these ratings. The only other concern is maximum current. A charge controller has a maximum current it can handle, they are generally model numbered this way, a Xantrex C-60 for example has a 60 amp rating. Add up the Imax numbers on the back of all your panels, this is the maximum amperage the panel should put out. As long as it is not above 80% of your charger controllers maximum amperage, your good. Take care, Rudydoo
Q:how can i build my own, cheap, solar panels at home?
Build from scratch, sorry your way over your head. (mine too). There are lots of companies that will give quotes on doing what your looking for, but plan on spending 20 to 50K depending on where you live and what you need. I don't know about where you are, but My hydro bill is almost half delivery charges. Therefore I could cut back by 99% on the usage, and still only have my bill come down by less than 50%. I understand you desire to lower costs, but unless you do a big change(lots of outlay) your savings will be small. By all means shut off lights your not useing etc. there are other ways of lowering your household bills better way is solar heating. But this also depends on where you live. I'm building a solar collector for 2 houses , Contact me at and I'll pass on more info

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range