Mono 300w Solar Panels from China CNBM Brand

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
1 pc
Supply Capability:
99999999 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Description:

CNBM Solar  is a world-leading and Vertical integrated manufacturer ofhigh-performance with Silicon,

Wafer, Cells, Modules, which convertsunlight into electricity for residential, commercial, and utility-scale

power generation.

        

The capacity of CNBMSolar is reach to 1GW, andmake sure each year our shipment capacity is more

Than 700-800MWs, at the same time, wehave set up the largest solar power station with our partner

in Ukraine.

       

CNBM is a Quality + Service orientedcompany with“Excellence at Each Step” approach, composed of

the finest components from TUV andIEC-certified partners around the world, CNBM modules consistently

undergo a variety of trials at thecompany’s Test & Development Centre, ensuring peak performance

capabilities. The company iscommitted to develop and provide the world with clean and renewable energy

to ease the energy shortages as wellas human kind’s impact on the environment.



Mono 300w Solar Panels from China CNBM Brand


FAQ:What's your products warranty?


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How to connect 2 power supplies together? (Solar panels)?
Most solar lamps use a single .2V nicd or nimh battery as a back-up supply, so they should be able to generate at least .5V in full sun to allow charging of the battery (you can verify the voltage of a single panel with your DMM) If you have two of these panels, I wouldn't expect them to make more than approximately 3V. The proper connection would be a series connection where the negative of one panel connects to the positive of the other and the remaining positive and negative wires become the outputs. Try this connection and measure again with your multimeter set to DCV and the panels in full sun. If the voltage is not high enough, add a third panel wired with its positive lead to the remaining negative of the first two. This should bring your voltage up another 50 percent.When you wire the panels positive to positive, negative to negative as you already have, voltage will be that of one panel, but current output will double (more amps) If you have many of these panels, you could combine series and parallel wiring to increase voltage and current.
Q:How to connect or use Solar Power Panels?
You will need help with this. Panels may or may not be 24 volt. If you can find a name tag, you can find out from the manufacturer's web site. Some folks hook them all in parallel. Mine are in series, to create 480 volts. the reason for going to higher voltage is to reduce power loss in the wiring. Even then, I used a wire size larger than recommended. The frames want to be interconnected, and wired to ground. The live conductors connect through disconnect switches to an inverter. The inverter is sized to the output of the panels. Where the utility allows net metering, the inverters are connected through a disconnect switch to the grid, which of course also feeds the house. Assuming you are on the grid, you will not need batteries. If outages severely impact you, you can have batteries. Counting against them is that they are costly, and use part of the power you generate, just to keep them charged. If you have batteries, it is usually best to rewire circuits so noncritical circuits are disconnected during outages. Leaving perhaps minimal lighting, fridge, freezer and critical medical circuits. Learn all you can from the Internet (try solar panels), and from the green search box above. Be sure to see if your state has a rebate program, and the conditions which it requires.
Q:How many Solar Panels do I need?
I okorder.com/... Home Power (magazine)
Q:solar panels for my home.?
You will first need to know how much power you'll be using. Follow the link I left and it will take you to a page that has an Electrical Load Computation Worksheet. It's about the fifth one down on the page. After that, you'll be able to figure out what you need and what it will cost. The page link I left has other helpful articles, too.
Q:I have a 6v solar panel , but a 3v dc motor doesn't run with that!!!!?
Because its not voltage related its current related. look at the start up values for the motor w respect to current. This will be listed in amps or milliamps. Then cross reference that to the output of your solar panel also listed in amps or milli amps... ;)
Q:what is the best solar panels to use on my new house(tube or flat)?
I assume you're talking about heating water. Based on what I've seen, the spiral tubes seem to heat the water to a higher temperature than the flat panels, probably because the water has to follow a longer path and has more time to heat. This type of panel will heat the water to a high enough temperature for almost any household application, but you need to be careful about how you set it up. I once saw a pool that had been equipped with that type of heating system, and it produced enough heat to melt one of the PVC pipes. It was a vertical pipe next to the filter, and it had fallen over onto the ground, pinching off the flow of water. This was in Arizona, so it may not get that hot in your area.
Q:Question about home solar panel systems?
As Ed said, that .2 kW is an instantaneous rating in bright sun. The way to do this right is to consult the maps here rredc.nrel.gov/solar/old_data/nsr... to find the number of equivalent sun-hours your location gets per day. Select, Average, Annual, Flat plate tilted south at latitude. A map will come up. For northern California, it shows 5 equivalent sun hours per day, for example. If the system is .2 kW, then .2 x 5 = 6.0 kWh of energy the system will generate per day, on average. That takes into account cloudy days, short winter days, long summer days, everything. The 2.4 kW system would give double that, obviously. But that's an example, based on a specific location. Phoenix would do better, Seattle would do worse.
Q:How to setup my home on Solar Panel?
good okorder.com lots of good ideas there
Q:Would you put solar panels on your home? and why?
Why: ) It's a great technology. 2) It has low impact to the environment. Why Not: ) Initial cost is substantial. 2) solar panel technology is greatly improving. I would hold out for a few more years when you can actually use it as a sustainable source and as a replacement source and not so much a suplimentary source.
Q:Solar Panels for home use?
For a starter you would look at how many watts you use. And how deep in you want to go. 80 watts at 2volts dc is nice.. But getting it to 20 ac. You will need a good inverter, battery's. There is things that you can replace in your house that will run on 2 volts. Lights fans. But to answer your question you would first have to look at what you use or and what you want to change over. I have got 900 watts of panels and 2700 Amp hours of battery's on one system. That will run all my lights computers and TVs Also on this I have converted a ups for the 20 VAC. I have been working on this for 0 plus years with no plans to finish. ( there is no end for what you can do with the power of the sun)

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range