Mini Dehumidifier with Air Fresh Function 2000ML

Ref Price:
Loading Port:
Ningbo
Payment Terms:
L/C,T/T
Min Order Qty:
500 Pieces pc
Supply Capability:
40000 Pieces per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

2000ML Mini Dehumidifier with air fresh function, 750ml/day de-humidification

 

De-humidification:750ml/day

Water tank capacity:2L

With air fresh

Voltage:AC110-240Vor 220-240V

Power consumption:AC75W; DC60W

Working by Electronic Module(Peltier system)

Automatic switch off when water tank is full with red LED indicator

Suitable for wardrobe,storage room,kitchen cabinet etc. of home,office,dorm

 

FAQ


Q 1.Okorder Quality Control?
We hold a very strict quality control system to check every connector of our products for

your safety.

Q 2: How do you care for your kitchen appliances?
A: Keep good Ventilation indoor. Open the doors of the kitchen appliances, if not. There

will be some mildew on cutting board and other kitchenware, because the water vapor can not

evaporate easily.
Keep clean of all the appliances. Each kitchen has its special cleaning fluid,please go to

Kitchen cleaning stores buy some clean them on time.

Q 3: Which one do you use the most of kitchen appliances?
A: Assuming you mean small appliances .I say too many! At one time we would buy every one

that came along; including a hot dog machine, pizza maker, elec. carving knife, elec.,

toaster oven,. Most have been garaged sale (sold) or are stored in the garage. Most used;

coffee maker, microwave, blender and mini food processor. OK?

 

 

 

 

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What is the principle of a hydrogen dryer?
Adsorption at a high temperature and partial pressure of water vapor at a high temperature and low water vapor partial pressure (regeneration)
Q:What are the factors that affect drying effect of dryer?
In the dryer, the first is to remove the moist air so that it contains very little residual moisture. The air is then heated to decrease its relative humidity. At this point, the steam pressure of the dry air is low. After heating, the water molecules in the particles escape from the bond force and disperse into the air around the particles
Q:What is the future development of dryers?
Large scale, high strength and high economy, as well as improvement of adaptability to raw materials and product quality are the basic trends in the development of dryers
Q:What are the methods of use of the dehumidifier?
The main characteristics of liquid desiccant: air humidity reduction range, at lower temperatures can also achieve good results. However, the concentration of hygroscopic agent should be adjusted in time, and the corrosion inhibitor shall be added with corrosion inhibitor to prevent corrosion of the equipment
Q:What are the characteristics of a convection dryer?
The humidity of the airflow has an effect on the drying rate and the final moisture content of the product
Q:When the automobile air conditioner is used, why is the dryer hot?
The dryer is mounted behind the condenser and the compressor compresses refrigerant to produce a high temperature, high pressure gas into the condenser. A semi fogging refrigerant, which is cooled by a condenser to about 70 degrees, enters the dryer. So the dryer is very hot and hot
Q:What are the common types of fluidized bed dryers?
The fluidized bed is dried in accordance with the dry material and has a liquid material suitable for suspension and solution.
Q:How to install the car air dryer?
The length of the line from the air compressor to the dryer shall be required to ensure that the air temperature at the inlet of the dryer meets the technical requirements
Q:What are the clogging problems in dryer?
Refrigerant can not cycle, low pressure for negative pressure, air conditioning is not refrigeration.
Q:What are the factors affecting the dryer?
In the air around the particles, the absorption of heat and the diffusion of water molecules to the surface of the particles take a certain amount of time. Therefore, the resin supplier shall specify the time required for the effective drying of a material at the proper temperature and dew point.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range