Q:What is the difference between coke and semi coke in ferrosilicon smelting process? In the process of energy statistics in the end should be 0.9714 of the conversion coefficient should be used with the conversion coefficient of 0.75 x 0.9714, please expert advice? emergencyUrgent!

The difference between them is that the final temperature of the two, the use of different raw materials, product yield and product properties are not the same. Low temperature coke. Under the condition that the coal is isolated from the air, the product is heated to 500 to 600 DEG C to obtain the product. It uses the raw coal is lignite, metamorphic degree of coal, long flame coal and gas coal. The final purpose of the low temperature carbonization is to obtain high yield coal tar

Q:After the long-term use of non stick pan, oil stains can not be effectively removed, over a long period of time in the non stick coating on the formation of a layer of coke, the effect of losing non stick. As a result of this layer of coke is relatively dense and smooth, scouring cloth has been ineffective, steel ball can not be used to damage the coating, what chemical or physical methods to remove this layer of coke?

Soak in hot water for a few hours (or a day and night).Two, with cooking shovel (Mason's Pihui knife is best) to remove surface soft.Three, the same with a spade close to the bottom of the pot to eradicate. Until the last thing left is black.

Q:The difference between coal and coke

The semi coke production tend to low temperature carbonization, distillation temperature at 600 degrees Celsius, due to a late start, at present the low temperature carbonization furnace single furnace annual output of 30 thousand tons / year in most equipment under low temperature carbonization furnace forum of more than 50 thousand tons / year scale is still at the exploratory and experimental stage, technology of the large-scale equipment is still not mature, can only achieve centralized mass production using a combination of multi furnace technology. The use of coal field is quite widespread, especially in the carbonaceous reducing agent has unique properties, economic advantages are very obvious.

Q:The chemical composition of coke is m10.m25

Abrasion resistance refers to the ability of coke coke can resist friction without generating surface of glass forming debris or powder, by the M10 value. The effect of the crack of coke crushing strength, M40 value, the influence of coke pore structure of abrasion strength M10 value determination method of.M40 and M10 was more in China the migon drum test in Germany. As shown in table 31-1.After the completion of the test, the sieve with the pore diameter of 40mm and 10mm screening, greater than the percentage of 40mm particle size is M40, less than 10mm of the particle size of the M10 value. The intensity of the provisions of China Metallurgical Coke indicators are shown in table 31-2.

Q:What is the concept, relationship and difference between coke and coke? The main difference and contact, thank you

6, the horizontal type coke oven drying machine(7) gas purification circulating water.... supporting technology(8) dry cooling technology of interlayer water-cooled steam.(9) microcomputer precise dosing system

Q:How to calculate the average particle size of coke

That is, "(volume) of the table of the percentage, in addition to the corresponding boundary value", these values are added, then the countdown. For example, the boundary 0 to 1 has a value of 10%, between 1 and 2, and between 2 and 4 has a value of 40%, and between 4 and 8, then D (3,2) = / (0.1/0.5 + 0.3/1.5 + 0.4/3 + 0.2/6) = 1/ (+ + 0.2 + + + 0.13 + +) = 1/0.56 = = =

Q:The chemical composition of coke m10.m25 refers to?

M10 refers to the wear resistance of coke, M25 refers to the crushing strength is the mechanical strength. Mainly the cold strength of coke. Coke is also the most important indicator is the hot state, CRI thermal reaction and CSR reaction intensity. In blast furnace production, both cold and thermal strength are important.

Q:What does the M40% and M25% mean in the analysis of coke?

(1) crushing strength (shatter strength): the ability of a certain particle size coal sample to fall under the condition of free fall.

Q:8 points will be isolated from the air to enhance the heat of coal, in addition to the main coke, but also the material listed in the following table: No.

Ethylene containing carbon carbon double bond can add poly to generate polyvinyl chloride, can be used for food packaging, reaction equation is: nCH2=CH2Initiator,The answer is: nCH2=CH2Initiator;

Q:Why in the blast furnace ironmaking with coke instead of charcoal why coke can produce heat to improve the heat of the furnace how to produceWhy in the blast furnace ironmaking with coke instead of charcoal why coke can produce heat to improve the heat of the furnace how to produce

The role of coke in the blast furnace: 1 reducing agent 2 heating agent 3 skeleton role. Combined with the effect of coke in the blast furnace can know compared with coke instead of charcoal. The coke oven gas is produced high calorific value of fuel, and is an important raw material for organic synthesis industry.