Q:Will paintless dent repair work on metal garage door panel? How do I find a contractor who does it?

look in yellow pages for auto body but if your door has a texture type panel it can only take out most of the dent but not a complete match.. for that you would have to replace panel

Q:I have a metal security door and frame that has come out of square. The top of the door is rubbing against the top of the frame, and it is very difficult to push close.If this was a wood door, Id probably shave it. Ive never dealt with this in a metal door. Whats the best way to fix it?Thank you!

The door has been sprung out of shape. First make sure all of the door hinge screws are tight. Try the door. There are corner brackets holding the frame together. Look for screws and tighten at all 4 corners. With a tape measure, check diagonally from corner to corner. The measurement should be equal. Press on door to spring into shape and correct measurements.

Q:cause the keys to my metal slide-door keeps bending and breaking.

You need to adjust the door or the latch or lube it, that lock should not be that hard to turn if everything is set up right!

Q:Whats the easiest way to put in a doggy door in a metal door? Its a metal door with a screen window

you're able to get plastic through fact it remains at a greater consistent temperature than steel through fact steel heats up and cools dow truly actual yet plastic does not and that's greater inexpensive and a canines has much less of of undertaking being injury in a plastic cage and the dimensions could be super adequate so as that it has a sturdy quantity of room to bypass around in even while it gets older and bigger so as which you dont might desire to bypass off paying for yet another crate each and each month or so through fact i be attentive to somebody that did that and that they wasted 1000 money in in simple terms 3 months

Q:Buy aluminum doors and windows to pay attention to what?

I am the decoration of this, it depends on where you live, and in the balcony to consider the appearance of fading, and whether it can withstand the invasion of sand. Installed in the toilet bathroom to think about whether the waterproof anti-electrochemical corrosion or something. There is also attention to noise isolation, thermal conductivity and other issues, such as the summer heat fast, then you do not open air conditioning, the same winter. These details should be taken into account. As for what brand is good, see how much you budget is slightly, the general luxury, villa decoration are like to use to send the doors and windows, if you have money, you can consider.

Q:Aluminum alloy doors and windows profiles 80,868 What does it mean?

Section is not the same Let's talk about the structure of aluminum alloy doors and windows: aluminum windows and doors windows and windows and windows and windows in two parts; window frame is a fixed part and the wall connection; sash and window frame is connected to push or flat open that part; 80,868 refers to the window frame profile outside the measurement thickness, not the thickness of aluminum; 80 on behalf of the aluminum frame profile size 80 thickness is 80mm, 868 is 86.8mm; The larger the number, the larger the thickness of the profile is, and the firmness is firm; the cost is high;

Q:Aluminum alloy doors and windows wheel bad, how to change the wheels.

Oh, oh, the original is 70B series, I give you solve! How much trouble? Look at your right side of the window fan screw hole, your seller fraud, save the material! Solution steps are as follows: 1 you first put 2 sash are pushed Side of the window to see there is not a white or other color of the plastic block? Some words to remove the screw to the side, so that the sash can be won. 2 window fiddle: two windows overlap, to avoid 1 inside Of the plastic block, and then together to lift up, and then pushed out to the outside, down, the sash to get the room, if the window from the outside ground is not high (non-building) directly to the outside to get the ground .3 will cross the window, The wheels of the side up, you use a cross screwdriver to mark your screws (both sides have) unloaded. Remove the screws, and then put this piece of material up hard to see, see the pulley, the same way to buy a change On the line. As for the installed, you can find where the wheels of the careful people, it would be estimated!

Q:permanent mark on a metal white door.

Try a Magic Eraser. Follow the instructions that come with it.

Q:Aluminum alloy doors and windows have what model

Hello, there are many models, basically every plant is not the same

Q:Im installing laminate and have noticed that the doors (4 doors) have a metal frame. Ive read everywhere that I should cut the bottom of the door frame (to lay the laminate underneath) with a undercut saw but how do I cut the bottom of the metal door frame?Ive thought about using a metal cutting blade attached to a drill but Im afraid of causing a fire!NOTE: two of the doors have several angles in the metal frame that stick out about 1-1.5 inch.I was told that a fein multimaster may do this cut.Thank you so much for your help.

DIY Doc is correct. You can rent the undercut saw, in most large cities, and use a metal cutting blade. Using a piece of the lam floor and underlayment as a depth guide you will make short work of the job at hand.