manual type hydraulic stacker

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

It's good looking and durable in usage.

It works flexibly and one person could operate and compelte working.

Usually used at fatory, warehouse, port,etc.

It uses hydrulic system for working.

Opertaion type: hand press, foot pedal

The material adopts good steel and welded steel.

loading capacity:500-3000Kg

Lifting height: 1600mm

lowest height: 90mm

fork length: 800-1000mm

width adjustment: 220/240-440/530/550/620mm

manual speed under manual control

It's widely used in industry of military enterprises , electronic appliances, machinery manufacturing, aerospace , medical , logistics, warehouse stores , automotive, food , railways, petrochemical, textile,etc.

Feature:

Easy operation

Flexible motion

up and down balance

low cost

on hydraulic station










Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:The photo of the forklift card is a few inches. Is it colorful?
I am a forklift driver training, as long as one inch of color picture is ok, the free crown, do not need blue bottom
Q:Can a power supply of 48-volt battery pack a 12 volt fan
If you don't have a 12V output. It can be connected directly from the battery pack, and the six battery units in series (which are 2V per unit in general, be measured with multimeter in advance), the lead is 12V. But be careful not to short-circuit your safety. It is best to be the first method, and the second method will cause the cell to be unevenly distributed, which will damage the battery
Q:Learn the forklift truck, will you be tired in the future?
Hello, the original poster can glad to reply for you I am the forklift worker get in March 2014 the ministry of construction of the forklift license Then apply for many recruiters say the local families don't admit I'm in the middle of April (April 2015) to enter oneself for an examination a pledges inspect bureau forklift license I like all kinds of car I have C1 driver's license To take an examination of a forklift license Although the job is not as high treatment as civil servants Don't like IT industry technician high-tech But it is also a live technical Ha ha Happiness consists in contentment I wish you a happy work Forklift worker I feel not tired After all, it's the brain is to drive tired attention I am in logistics warehouse forklift I think can also may be young I have a study colleagues together She ratio I big a lot of running a forklift in the enterprise workshop wages in January three thousand In January two days off Went to work at 9 o 'clock every morning At noon to eat an hour Dry until five o 'clock in the afternoon very tired
Q:What is the responsibility of the forklift driver for the job?
If the driver of a forklift truck is employed, the unit shall be liable for compensation. If the driver of a forklift is employed by an individual, the employer shall bear the liability for compensation. The two sides may negotiate a compensation dispute in advance and fail to bring a suit to the court.
Q:What is the difference between a forklift and a trailer for a hydraulic drive?
The so-called hydraulic drive is the idea of automatic stop, which is not disconnecting, only the throttle and the brakes. The rocker, which moves forward and backward, is usually positioned at the wheel. As for leaning and lifting, you can go to the scene and pretend to be a professional
Q:What's the matter with forklift
(2) the ball head of the rod is adjusted. (3) the steering screw is adjusted too tightly or the bearings are damaged. (4) the steering gear is lubricated by lubrication, such as oil in the steering machine. The ball section is not lubricated in time to increase the friction resistance. Diagnosis and discharge to turn the steering wheel, such as feel at ease, that good steering machine interior, should check whether transmission mechanism with tight and poor lubrication, adjustment, lubrication when necessary
Q:Battery lift truck charging requirement
Different types of charging machine output parameters are different, and the method should follow the instructions of the charging machine. The electric forklift truck. The wire and socket should be checked before electricity is damaged. If any damage is found, it should be repaired and replaced before recharging. 3, check whether the battery is intact and wiring are in good condition, and open the charging flap, observe the electrolyte is in accordance with the provisions of the liquid level height, add distilled water when necessary, the injection liquid level higher than protective piece of 15 to 20 mm advisable.
Q:Special equipment, the type of vehicle for forklift licence and corresponding driving vehicle
The N2 forklift card can drive a forklift: 1, there is no limit to the type of driving car, and the tonnage can be opened. 2, short for "motor vehicle driving license", and "driving licence", in accordance with the law personnel required for motor vehicle driving licenses, previously known as forklift driver, now change to code, forklift driver code is N2. 3. The forklift driving is special operations, issued by the state production safety supervision and administration of the People's Republic of China special operations card ", forklift, generally are tools, only used in the unit within the work place. So generally speaking, you only need a position certificate or a license, but the average unit will ask for a driver's license.
Q:How many years can you use a forklift battery
The battery will produce the gas during the charging process, should keep the charging area ventilated well and there is no open fire. 4, in any case, in the process of charging the electrolyte temperature should not exceed 45 ℃, otherwise should try to cool down, such as to reduce the charging current, measures such as artificial cooling or pause charge, after waiting for the temperature drop charge again. It is strictly forbidden to put metal tools on the battery. There is no excess clutter on the battery.
Q:How to start a forklift? Say detailed point
Before leaving the forklift: the door stands slightly forward, and the cargo fork naturally lowers; If a cargo fork does not fall to the ground, there is a danger of stumbling and harming the body; The direction handle is in the neutral position; Pull on the brake handle; Turn off the key and remove the key. Parking in designated places: the parking area must be strong enough; Stop where traffic is safe; Not to park in the vicinity of fire hydrants and affect fire control passages; Stop at or near where inflammable substances are made; Don't park your car on the slope. Charge: to prevent the charging device from being damp, and the ventilation condition in charge of the charging station is better to emit the smell from the battery. When charging the forklift battery, be sure to mark the charge. When the battery is charged, the positive and negative are unable to take the reverse. Do not overdischarge, do not use the forklift truck to stop, when the battery capacity alarm is flashing, the battery needs to be charged. On the incline, Empty car up and down the slope - if the car is over the slope, it needs to be rolled back up and down the slope. The center of gravity will fall on the front wheel. Go up and down the slope.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range