Magnesite Alumina Brick for Ladle Bottom and Wall Parts

Ref Price:
Loading Port:
Tianjin
Payment Terms:
TT OR LC
Min Order Qty:
1 m.t.
Supply Capability:
2000 m.t./month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Description of Magnesite Alumina Brick

Magnesite Alumina Brick for Ladle Bottom and Wall Parts are shaped by using top grade bauxite and corundum as aggregates and phenolic resin as binder and focusing on strengthening the matrix. Magnesite Alumina Brick has the characteristics of corrosion resistance, spalling resistance, high strength, anti erosion and etc., applicable to the ladle bottom and wall parts.

 

Specifications for Magnesite Alumina Brick Bricks

 

Items  Al-Mg-C Bricks  Mg-Al-C Bricks
 AMC-60  AMC-65 AMC-70  AMC-75 MAC-75  MAC-70
    Chemical Compositions (%) ≥  MgO 12 10 8 8 75 70
 Al2O3 60 65 70 75 1015
  C  6 6  6   6   6   6
  Apparent Porosity (%) ≤ 8  8   8   8   8   8
  Bulk Density (g/cm3)  ≥  2.85 2.9 2.95 2.95  2.9   2.9
  Compressive Strength (Mpa)  ≥  45  45   45   45   45   45

 

Features of Magnesite Alumina Brick Bricks

Low bulk density, low thermal conductivity, good thermal insulation performance.

Refractory category allow direct contact of fire, suitable for various atmosphere.

Good integrity with furnace lining, long service life, easy operation, could be shaped freely.

 

Typical Application of Magnesite Alumina Brick Bricks

Furnaces of metallurgy industry, heat treatment furnace.

Furnaces of chemical industry and construction industry.

Furnace of incineration of garbage, recirculating fluidized bed furnace .

 

Our Service

we can arrange the production as your requirement  and drawing

Techinical support after sale

We conduct strict inspection in the production proess and make sure the product standard.

Manufacturer with large capacity,ensure the fast production cycle after confirmed the order.

 

 

 

 

 

 

 

 

 

 

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How can the refractory brick blast furnace be pulverized and pulverized enough not to be taken away by the wind?
Because the hot air outlet of the top burning hot blast furnace is high, the installation requirement of the hot air manifold is high, and the requirement of the strength of the pillar structure is higher, so the rectangular arrangement of the hot blast stove is arranged. The top burning hot blast stove is located on the furnace top because of burner and hot air valve,Therefore, operation, maintenance and installation all require mechanization and automation. Also, because these water cooled valves are mounted with a high elevation,Therefore, the demand for cooling water supply pressure should be improved accordingly, the use of large top burning hot blast stove, the key lies in the design of high-power high-efficiency short flame burner. The top combustion hot blast furnace absorbs the advantages of internal combustion and external combustion hot blast stoves, and overcomes some of their shortcomings,Its structure can meet the requirements of modern blast furnace for high temperature, high pressure and large scale development,Combustion capacity, while meeting production requirements, has been successfully reduced by many devices,
Q:Aluminum content 38. silicon content 55 What refractory bricks?
Semisilica brick: the content of Al2O3 is 15% ~ 30% of aluminium silicate refractory products. Manufacturing products are semi silica quartz containing impurities or native clay kaolin, refractory clay or kaolin beneficiation tailings and the pyrophyllite
Q:How to reduce porosity of high alumina brick
When proportioning, the ratio of coarse to medium to fine is 4:2:4, and the maximum particle size should be no more than 5mm. The mixing order is as follows: first adding coarse particles, then adding sulfite pulp waste liquid, premixed 3min, then adding high aluminum fine powder for mixing. The operation process is coarse and fine particles added in sulfuric acid with crushed pulp waste.In order to reduce the porosity, our company suggested that the single-sided pressure changed to double-sided pressure instead of double-sided pressure, the number of strikes should also vary according to the amount of feeding. If the kiln is fired, the location of the fire hole shall be adjusted so that the middle part is dense, the edge is thin, and the door near the kiln is properly encrypted so that the temperature difference between the furnace top and bottom and the temperature difference between the inside and outside are not greater than 20 degrees.
Q:The difference between light high alumina brick and heavy aluminum brick
Lightweight high alumina brick, also called high alumina insulation brick. Alumina content of 48% or more, mainly from mullite and glass phase or corundum composition of lightweight refractory. Volume density 0.4 - 1.35g/cm3. Porosity 66% - 73%, compressive strength 1 - 8MPa. Better thermal shock resistance. Usually, a high alumina clinker is added with a small amount of clay. After grinding, it is poured and shaped in the form of slurry by gas generation or foam method, and it is fired at 1300 - 1500 DEG C. Sometimes industrial alumina can be used instead of some bauxite clinker. Used for lining and insulation of masonry kilns, as well as for areas where there is no strong, high temperature molten material erosion and erosion. When contacting the flame directly, the surface contact temperature shall not be higher than 1350 degrees centigrade.
Q:Application characteristics of high alumina brick
Load softening temperature. The softening temperature of high alumina brick products decreases with the increase of silica and alkali metal oxide content, but is higher than that of clay brick products, which is about 1420 - 1530 degrees centigrade. Al2O3. The softening temperature of corundum brick with content greater than 95% can reach above 1600 DEG C.
Q:What is the standard classification of high alumina bricks or high alumina bricks?
High alumina brick is a kind of refractory material in refractory brick products. It is made of refractory clay or other refractory material. It belongs to the product of Si Al System
Q:Difference between low creep high alumina brick and ordinary high alumina brick
The question is good, these two belong to the high aluminum brick products, when many manufacturers buy, I do not know how to distinguish.
Q:What are the grades of high alumina bricks?
According to the size of high aluminum brick is divided into: standard brick, special-shaped brick.
Q:Refractory brick, high alumina brick, magnesia chrome brick or magnesia brick, clay brick, which type of high temperature refractory brick?
High alumina brick clay brick up to 1700 degrees above 1500 degrees -1750 degrees of magnesia brick and magnesia chrome brick 1500-1650 degrees, I is the production of clay brick, brick my temperature at 1500-1700 degrees. Specific depends on what kiln, brick is only part of it
Q:What is the content of free silica in the refractory bricks of high alumina bricks?
Refractory powders are not rich in free silica in varying degrees

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range