LONKING Brand Wheel Loader CDM833D with 1.7CBM Bucket

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
1 unit
Supply Capability:
500 unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Construction Machinery CDM833 features:

Powerful WEICHAI DEUTZ Engine
Hydraulic Transmission & Torque Converter
Pilot Control as Optional
Standard Air Condition
Variety with Attachment
Convenient Maintenance

Weichai Deutz WP6G125E22 engine brings great power with low fuel-consumption.
Lonking self-made radiator as standard with great radiating efficiency which has been tested by the practical condition,Enlarged fin-distance radiator as optional choice.
CDM833 can select machinery flexible control or pilot control. 
New-type fuel tank with 200L capacity can increase the working time.
CDM833 is standard equipped with detachable cab, Which is very convenient for container delivering. 
Efficient and healthy air conditioner.
Enough space for operation and maintenance.Select many kinds of optional working devices.


Overall Data


Steering System

Bucket Capacity (m3)

1.7

Type

Hydraulic Load Sensing System

Rated Payload(kg)

3000

Cylinders-bore×Stroke(mm)

2-80×315

Operating Weight(kg)

10760±300

Steering Pump

Gear Pump

Traction Force(kN)

97±3

System Pressure(MPa)

14

Breakout Force(kN)

100±3

Flow Rate(L/min/rpm)

88/2200

L×W×H(mm)

7140×2500×3220

Steering Angle

±35°


Hydraulic System

Travel Speeds (km/h):

Lift Cylinders-bore×Stroke(mm)

2-125×784



Tilt Cylinder-bore×Stroke(mm)

1-140×553

Forward

6.5

12.0

32.0


Model of Working Pump

Gear Pump

Reverse

6.8

12.5

33.5


Flow Rate(L/min/rpm)

176/2200

Engine

WEICHAI WP6G125E22

System Pressure(MPa)

16

Rated Power(kW·hp/rpm)

92·(125)/2200

Pilot Control System Pressure (MPa)

2.5

Peak Torque(Nm/rpm)

500/1400-1600

Hydraulic Cycle Time, Rated Load in Bucket(In second):

Starting Voltage(V)

24

Raise(Loaded)

Dump

Lower(Empty)

Total

Drive Train

5.5

1.3

3.7

10.5

Torque Converter

Single-stage, Single-turbine, 3-element

Electrical System

Torque Ratio

3.45

System Voltage(V)

24

Transmission

Countershaft Powershift Transmission

Battery (2 in series)(Ah)

105

Gear

3F/3R

Lamp Voltage(V)

24

Pressure of Transmission(MPa)

1.2~1.5

Service Refill Capacity

Main Reducer

Spiral bevel, 1-stage Reduction

Fuel Tank(L)

200

Final Reducer

Planetary Reduction

Hydraulic Tank(L)

173

Tire

17.5-25 L-3 12PR TT

Crankshaft(L)

17

Brake System

Transmission(L)

36

Service Brake

Single Circuit Caliper,Dry Brake

Front Axle(L) /Rear Axle(L)

18.5/18.5

Setting Pressure (MPa)

0.78

Air Conditioning System

Parking Brake

Flexible Shaft Controlled Caliper

Heating Capacity(W)

5000 (±10%)

Emergency Brake

Flexible Shaft Controlled Caliper

Cooling Capacity(W)

4200 (±10%)


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What are the transmission systems of the loader?
The first and second turbine output shafts of the torque converter and the upper gear of the torque converter transmit power to the transmission. An overrunning clutch is arranged between the two input gears.The transmission is a planetary power shift gearbox with three stalls with two brakes and one latching clutch. The forward, the I and the reverse gear respectively have respective brakes to realize the shift. Forward II gear is achieved by combining locking clutch.The driving axle adopts double axle drive, the main drive adopts a first stage spiral bevel gear reducer, and the left and right half shafts are full floating type.2. loaders in the form of work: the former imperial, rotary, after the imperial styleFront imperial style: front shovel loading and unloading, simple structure, reliable work, good vision. Suitable for all kinds of working sites;Rotary type: the working device is mounted on a turntable which can be rotated from 90 to 360 degrees. Side unloading without shunting, the operation efficiency is high; complex structure, large weight, high cost, poor stability of side, suitable for narrow site operation;After unloading, front-end loading and unloading at the rear, high operation efficiency, poor operation safety and wide application.
Q:what is the difference between the front loader washer/dryers compared to the top loader ones, and best brands?
Here are some differences between top- and front-loading washers: Efficiency: While a top-loading machine requires enough water to cover all the clothes in its drum, a front-loading washer needs only a third of that amount because its drum is set horizontally in the machine. As the drum turns, it uses gravity to drop the clothes back into the water. And while a top-loading machine will empty the soapy water and refill for a rinse agitation cycle, a front-loading machine just sprays clean water on the load as the drum continues to turn, saving gallons. Since there's no agitator in a front-loading machine, there's a lot more room for dirty clothes - and larger loads means fewer loads. Finally, the front-loading machine's spin mechanism can reach up to 1,400 rpm, as opposed to the standard top-loader's average 650 rpm. That means less water left in the laundry, which in turn gives you a shorter drying time, saving energy there, too. Space: Most front-loading washers can be stacked with a companion dryer, an impossible feat for standard top-loaders, except for a mere few models. If floor space is important to you, a front-loading washer is the better choice.
Q:mag loaders?
Speed loaders are made to fit specific magazines, not guns. Some magazines will work in more than one gun, so your speed loader naturally can be used for loading the magazines for those guns. Speed loaders really do not speed up the loading process. Their main purpose is to make it easier on your fingers and thumb because if you load a magazine several times or have several magazines to load it can take a toll on your hands.
Q:JCB Backhoe Loader??
python okorder.com its free and its me
Q:Is the loader subject to annual inspection?
According to the State Council "Regulations" special equipment safety supervision, quality inspection administration issued the "supplementary" catalogue of special equipment, clear into the special equipment field (plant) in special vehicles, excavators, loaders, scrapers and machines no longer belong to the field (plant) in special vehicles, local quality supervision departments no longer loader, scraper and backhoe loader of excavator, the workers issued a "special equipment operating personnel certificate", it is no longer on the personnel documents examined.
Q:How to install the windscreen of the loader?
1 find a rope; the thickness is approximately the same as 5 meters long strip wing;2 put the glass under the car on the bar; then put it on the outside with the rope as tight as possible;
Q:How long is the warranty on the loader?
The loader's warranty and quality is now divided into brand shelf life is generally 1 years or 2000-2400 hours is the main engine crankshaft cylinder (some wearing parts such as oil seal, Paul 6 months)
Q:how to upgrade icoo loader?
Icoo loader is only used by porn sites to transfer large files (movies). I'm sure if you go to the original pornsite you downloaded it from then follow the link you can get the latest version.
Q:Home Depot - Lot Loader?
You are called whenever anyone needs help loading their car. You are also in charge of the parking lot. Making sure the carts are put away and trash is picked up. You will also have to help the cashiers with trash and whatever else. Good luck, but if the store is cutting hours, you will be the first to have you hours cut. I worked at home depot for 2 years and the lot attendants were always the first to lose hours so you might want another part time job! Good luck! If they interview you, unless you really screw up, you will probably get the job. They hire everyone!
Q:Viewloader high loader paintball gun?
You mean the Viewloader High Voltage? It's ok. Low quality but it gets the job done. They're $45-50 brand new online so if he'll sell it for like $25 then it's a good deal. You may also need a tank hopper. Co2 tanks are about $10-20 depending on size and the hopper can be a plain gravity-fed, which are like $5. Eventually, you'll want something better but that's a good gun to start with.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range