LONKING Brand Single Drum Road Roller CDM520A6

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
1 unit
Supply Capability:
500 unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Construction Machinery CDM520A6 features:

A SERIES SINGLE DRUM VIBRATORY ROLLERS
Front & Rear Light For Night Operation
Panoramic Cabin/Tiltable Column
Close-Loop Hydraulic Vibration System
Rexroth Hydraulic Components
Wear And Impress Resistant
A/C & Pad Foot Optional



Weight Load

ModelCDM520A6
Operating Weight (kg)20000
Distributed Weight for Drum(kg)97000
Distributed Weight for RearWheel(kg)10300
Compact  PerformanceStatic Linear Load for Drum(N/cm)470
Frequency(HZ)28/33
Nominal Amplitude(mm)1.9/1.0
Centrifugal Force(kN)400/280
Maneuverability PerfomanceDiameter of Drum(mm)1600
Width of Drum(mm)  (W2)2130
Rim Thickness of Drum(mm)36
Length﹡Width﹡Height(mm)(L﹡W1﹡H)6298﹡2280﹡3096
Min .Ground Clearance(mm) (h)427
Min .Steering Radius(mm)6500
Wheelbase(mm)  (L1)3430
Travel Speed(km/h)Forward2.5/5/8.2
Reverse2.5/5
Gradeability30%
Steering Angle32±1°
Swing Angle±10°
Tyre Specification23.1-26 12PR
EngineManufacturerShangchai
ModelSC8D175.1G2B1
Rated Power(kW/rpm)128/2000
Min Fuel Consumption(g/kW•h)223
CapacityStorage Battery (V/Ah)12V﹡120Ah﹡2
Fuel Tank(L)350
Hydraulic Tank(L) 120
OthersDrive TypeMechanical
Vibration SystemClose-loop Hydraulic Vibration System
Service BrakeAir Booster Caliper Rear Axle Brake
Parking BrakeShaft Controlling Brake of Gear Box


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Wii Backup Loader/Launcher OR Neogamma R7 On 4.3U?
Wii Backup Loader
Q:How can I repair the pressure in the loader gearbox?
(three) the gear box oil level of the oil level is too low when the gearbox oil level is too low, the oil cycle to work up transmission oil in the residence time of oil bottom and natural cooling time is short and the cooling effect is poor, resulting in transmission of fever, will also cause the hydraulic pump suction air, resulting in the decrease of pressure in the system. This kind of failure, strain gauge pressure instability and large swing, the engine speed changes, pressure gauge readings without big changes, indicating that driving hydraulic pump has suction phenomenon or inlet pipe leakage phenomenon. Should always check the oil level and add sufficient hydraulic transmission oil, if found leakage, timely maintenance. The oil level is too high. The oil level is too high transmission high speed rotating element around too much oil, the friction resistance increases, the oil temperature rise and converted into heat energy to participate in the work of the oil circulation, slow heat can not be distributed in a timely manner, and the backlog gradually with the extension of working hours, the temperature increased. (four) continuous high load loader such as long time high load operation, the heat generated in the cooling speed is fast, the working oil temperature will overrun, the temperature reaches a certain level will have a great damage to the moving parts, so it is prohibited for a long time overload operation when the ambient temperature is high, more attention should be paid to. To sum up, in order to avoid the transmission oil temperature is too high, users should strengthen management, according to the provisions of the use and maintenance, to avoid oil shortage, water shortage and long time overload operation and so on.
Q:What's the brand of a small loader, 4102 engine?
Note that torque converter oil (also known as hydraulic transmission oil) cleaning, can not be missing, and then pay attention to do not heat, this type of car ran Louis high temperature (some brands this problem is better)Pay attention to maintenance according to instruction
Q:What Kind Of Hoppers/Loaders Should I Buy For My Tippmann 98 Custom And My Spyder MR1?
for the tippmann, get the cyclone feed system. for the spyder, got to action village and order a ricochet apache loader.
Q:How do I get usb loader on homebrew chan 4.3?
Make sure when you load the usbloader into your DS card that it follows this format sd:usbloader sd:appsusbloader The apps folder is what is accessed in the HBC and when you execute the app it will call the sd:usbloader I highly recommend looking into this site if you want to look into more wii apps. Theres even a wii app that connects you online on your wii to download and install more apps. Check out Chapter 3 in the guide below to properly configure your sd card. If it still doesn't work, start the guide from the top to make sure you have all the patches (IOSs) loaded in your wii properly to run usbloader
Q:Moms with front loaders - do you like them better than top loaders?
I okorder.com/ I bet ya money some of the people who have thumbed me down in the past have later on ran into these same issues and by now hate their stupid machine. They probably even have thought of my answer a time or two as they pulled they're funky smelling clothes out of the wash.
Q:I have a loader, but I don't live. It's alive
Buy Engineering machinery do not blindly buy, first you have to do is long and there is a job to buy machinery, engineering machinery because of depreciation and maintenance labor costs too much,
Q:Wii, Installed home brew for 4.2 what next? USB Loader or other? Hard drive iso play?
my okorder.com/... i suggest using the usb drive formatted to FAT32, with a folder on it called wbfs. inside this folder, you place wbfs files, which can be converted from iso or ciso files to wbfs using wii backup manager. once the files in wbfs format re on the usb rive, and usb loader configurable is installed, simply open usb loader configurable, and click the 1 button (i think), and go to the option to download all missing cover art. it will give you game case pictures for all the games you have on your usb drive,which will be saved on the SD card.
Q:Do I have to use the special laundry detergant for my fornt loader machine?
Mine is the same way, but we have a capartment for softner. You can try to used the normal stuff but use like half as much as you would on a normal washer. The reason why you are supposed to use the special HE stuff is because of the suds factor. Also since the front loaders use less water than a top loader they need a detergent that rinses out easier.
Q:Where can i get an iso loader?
There okorder.com/... Good Luck.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range