LONKING Brand Single Drum Road Roller CDM512D

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
1 unit
Supply Capability:
500 unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Construction Machinery CDM512D features:

D SERIES SINGLE DRUM
VIBRATORY ROLLERS
Front & Rear Light for Night Operation
Panoramic Cabin / Tiltable Column
Close-loop Hydraulic Vibration System
Wear and Impress Resistant
Powerful DF Cummins Engine

ModelCDM512D
Operating Weight (kg)12000
Length*Width*Height (mm)5978*2280*3220
Weight Burden on Front Drum (kg)6500
Weight Burden on Rear Wheel (kg)5500
Static Linear Load (N/cm)303
Min. Turning Radius (mm)6500
Travel Speed (km/h)0-10.8
Gradeability (%)40
Vibration Frequency (Hz)30/36
Nominal Amplitude (mm)1.8/0.9
Centrifugal Force (kN)270/180
Engine (DF Cummins) Model6BTA5.9-C150
Min. Fuel Consumption (g/kWh)206
Rated Power (kW/ rpm)112/2200
Fuel Tank Capacity (L)280
Vibration Pump Imported Variable Piston Type
Vibration Motor Imported Variable Piston Type
Steering Model Hydraulic Steering
Axle TypeFront Reduce + Middle Reduce + Wheel Hub
Tyre23.1-26 8PR
Service Brake Type Hydraulic Lock Front and Rear Brake
Parking Brake Type:Oil Cut Front and Rear Wheel Brake
Hydraulic Oil Tank Capacity (L)90
A/C ModelGK15-5.0Y2
A/C Refrigerating Capacity (w)4500
A/C Heating Capacity (w)5800


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Lee Classic Loader kit a good way to start reloading?
If I were you, I'd rather not. I started with one and after about 50 rounds I had enough. slow, labor intensive, and I discovered I needed a full length sizing die. so those 50 rounds i made were useless, because the classic kit did not have the right die, none of the rounds were sized right. I'd go with a entry level setup, like the Lee challenger single stage press kit for $125. (add dies supplies it's $200) or you cna do what I did next - a really stripped own setup Lee cast press (the $25 one) Lee dies set ($25) Dial Caliper. ($8) Lee Autoprime ($20) and that's all you'll need. the dies set includes powder measure load table.
Q:muzzle loader or shotgun?
for deer, i would go with the muzzle loader every time. Especially if i were in a position to ask. muzzle loaders have a bit more range. YOu wouldnt have to be extremely close. Shotguns lose their killing power in under 100 yards. At that range the deer is more likely to sense you, and be gone with its bad self,
Q:How do i properly use this front loader washing machine?
If you're a woman, I would recommend reading the manufacturers instructions. If you're a man, I must ask...... why the hell are you asking questions like that? Do you want to continue doing laundry as one of your regular chores? Plead ignorance, screw it up.... and guaranteed, you'll never be asked to perform the task again.... ever! (LMAO)
Q:how do i mount a front-end loader on a john deere 2850?
Depends on who made the loader, as there's several after market company's as well as JD that make them, best bet is to go to the manufactures website and find the installation instructions. as per model number, if this is a new installation and your tractor has not been set up with the auxiliary hydraulics for the loader yet you may want to seek professional help,
Q:Lee Loader Reloading Question? 7.7 jap?
I believe that since the Lee Loader only neck sizes the case, you could maybe use a .303 die. However, the Lee Loader makes no provision for trimming your cases, and when neck sizing you may experience problems with chambering. Particularly in different rifles of the same caliber. Many get dies from lee, for a press, that allows them to trim 30.06 brass, then reform it for the Jap. I think in the long run, reloading with a press will prove a better solution to your problem.
Q:Which is the land of the free?
religious institutions
Q:What companies use loaders in general?
The loader is a kind of engineering machinery, as the name implies, where the project is loader useless, like building, highway, railway, freight yard, stone factory, Sunaba, char steel and other heavy industries, and special purpose, mounted on the clamp fork, used in the field of wood.
Q:My halo B loader won't turn on?
If you put fresh batteries in it, then the guy probably sold you a broken Halo. Sounds like it needs a new board. You need to be careful on OKorder. You can get new loaders at good prices, the Invert Too is basically a Halo and it's pretty cheap. Edit- File a complaint with OKorder and give the guy a bad rep if he won't help you.
Q:breaking a muzzle loader barrel in.?
I gues the best thing to do is read the manufacturer instructions and do what it said to do
Q:Where can i find a prometheus ISO Loader download link to chip my psp?
iso loader just for TN cfw. you can play iso/cso directly without using iso loader. here ISO LOADER 1

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range