Light Steel Villa for South America

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
20000㎡ m²/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

This product belongs to Ligth Steel Frame Structure.

This structure is formed by the dense light steel studs and compound envelop and with all kinds of supprior physical qualities.

Advantages:

1. Flexible combination
2. Easy transportation
3. Fast construction
4. Cost saving
5. Removable & recycle

6. Thermal Insulation
7. Seismic and wind resistance
8. Roof Load-bearing

Packing:

light steel packing: light gauge steel in bulk, decorate panel material in pallet, other fittings all in boxes, loaded into 40' GP and 20' GP on container.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How to make geomembrane inspection?
The testing standards of geomembrane: 1. GM1 ultrasonic method evaluation joint 2. GM2 anchoring movement insert depth 3. GM3 large-scale hydrostatic force anti-puncture test (see ASTM D5514) 4. GM4 three-dimensional geomembrane tensile test (see ASTM D5617) 5. GM5 (a) polyolefin resin or geomembrane notched constant tensile load (NCTL) test (1992) (see ASTM D5397) 6. GM5 (b) polyolefin resin or geomembrane single point NCTL test (see Appendix ASTM D5397 ) 7. GM5 (c) polyolefin geomembrane joint joint constant tensile load (SCTL) test 8. GM6 dual-channel joint geomembrane high-pressure airway test 9. GM7 chemical welding method geomembrane joint peeling accelerated solidification test 10.GM8 quarry-faced geomembrane core layer thickness measurement (see ASTM D5994) 11.GM9 geomembrane low temperature joint 12.GM10 HDPE geomembrane sheet stress cracking resistant standard 13. GM11 conduct geomembrane accelerated aging test with fluorine light irradiation device 14. GM12 measure the roughness of quarry-faced geomembrane with depth indictor 15. GM13 high density polyethylene (HDPE) geomembrane test characteristics, test frequency and recommendation guarantee 16. GM14 take samples and choose a variety of intervals for geomembrane non-destructive test joint samples with characteristic test method 17. GM15 confirm bonding between layers of reinforced geomembrane 18. GM16 geomembrane surface cracking observation 19. GM17 linear low density polyethylene (LLDPE) geomembrane with smooth and rough surfaces test characteristics, test frequency and recommendation guarantee 20, GM19 LLDPE HDPE welding shear peel strength
Q:Production of fire paint business should have what qualifications
License, organization code, tax registration certificate, system certificate, etc.) and type approval certificate
Q:At present, the application of aerated concrete blocks is wide, what is its substantive advantage? And how to determine its superior performance?
As for the superior performance of aerated concrete blocks can be determined according to the following points: compressive strength, flexural strength, freezing and thawing, insulation properties, sound insulation, sintering rate, the specific identification of the country has a specific testing standards
Q:What is the telephone door event in Italy?
Q:What are the main points of paving HDPE geomembrane?
Q:Density board, multi-layer board Why should the number of units as a unit, what standard Mody, a variety of plate is a number of sheets?
In order to facilitate the transport and storage, these two kinds of plates will be packaged, a packaging is one, there is no standard, the number of thick less, the number of thin more, for example, we used to play 18% of 40, 50 or 75 sheets one.
Q:Tiling bathroom please help!?!?!??
Bnose tile is a new simplified way of doing tile and was to remove one of the grout edges. So all you have to do is grout the top like they did in the old days a few years ago. You could also use a thin lat of flat trim, a brass or stainless steel edging, or caulking that matches the wall or tile. I think the simple grout is your best bet. PS. Where corners meet If the tile is same color through they can show. If it is glazed colored or just a thin color on top then no. In that case cut the tile back so that they do not quite reach the corner. Then there will be a slight inverted corner where you will grout or caulk. In neither case would you want to miter the corner. It will be too sharp and thin corners would be weak enough to chip.
Q:What are the noncombustible materials?
The flame retardant processing of various types of flame retardant fabrics Polyvinyl chloride plastic, phenolic plastic, polycarbonate plastic, polytetrafluoroethylene plastic. Melamine, Urea-formaldehyde plastic, silicone plastic decorative profiles, all kinds of fabrics, such as flame-retardant treatment
Q:How can you tell the difference between wall tiles and floor tiles?
Wall tile is on the wall and floor tile is on the floor. Seriously, there's no real difference. Although, floor tiles are generally bigger (12+ inches square), while wall and counter tiles are more like 4-6 inches square.
Q:Antistatic floor how much money
Anti-static floor pavement is generally divided into anti-static tiles, PVC anti-static floor and anti-static floor. 1, anti-static tiles 2, PVC anti-static floor child often powder at the beginning of mad Mad Fu 3, anti-static floor 4, ceramic anti-static floor 5, all-steel anti-static floor 6, aluminum alloy anti-static floor

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range

Premium Related Products