LED T5 Tube 1.5m SMD Chip High Efficiency 18W

Ref Price:
$9.88 / pc
Loading Port:
Shenzhen
Payment Terms:
TT
Min Order Qty:
10 Pcs pc
Supply Capability:
100000 Pcs Per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

LED T5 Tube 1.5m SMD Chip High Efficiency 18W 1. This product meets the standard of CE certification.
2. With internal No-isolated power supply.
3. Round and the elliptical tube are available.
4. Use the most mature international well-known LEDSMD2844 as the light source, which can ensure the led tub35 as the light source, which can ensure the led tube brightness and long lifetime, also can reduce the light decay.
5. Use the high quality aluminum PCB for LED’s better heat dissipation.
6. High-grade PC cover with nice light transmittance(> 95%),Transparent PC cover and frosted PC cover are available.
7. 180 degrees beam angle makes the lighting effect better.
8. CRI(standard products)>70,it can be over 80 if required.
9. Ambient temperature:-20°C-40°C, surface temperature: 42°C-45°C
10. No mercury, lead or other hazardous materials; no radiation, no electromagnetic radiation, no frequency flash, instant start up, no hurting eyes.
Applications:
Replacement for conventional fluorescent tubes:
1. Hotels
2. Conference/ meeting room
3. Commercial Complexes
4. Residential/ Institution Buildings
5. Schools, colleges & Universities
6. Hospitals General li

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How do I get the four joints of the LED fluorescent tube
I can't put a picture on it, you can try it yourself, add a rectification bridge at each end of the tube, and then you put the positive plus positive on both sides, negative plus negative, onto the next bridge
Q:What is the cause of the lights after the led fluorescent lights are turned off
The second the problem is less But the most easy to test leakage is chip Or a chip resistance capacitance are stored This can be got, through testing machine performance
Q:What is the difference between a radar sensor and an infrared LED fluorescent lamp?
Infrared inductance LED fluorescent lamp: inductance distance is general, Angle is relatively small, the influence of environmental temperature dust is big, in 37 degree circumstance, the sense distance can shorten. (the detection of infrared sensor head needs to be revealed, not easy to install).
Q:Can the T5 light tube be free of ballast?
The T5 bulb must be ballast, and electronic ballast, no ballast to light the T5 lamp.
Q:Put on the new light bulb, why the lamp still not bright
If there is a problem in the ballast itself, if the lamp filament of the inductor is red but can not be activated, most of the regenerator short-circuit damage.
Q:How is the T8LED fluorescent lamp installed?
Installation is simple, make sure your lamp is single head unipolar or bipolar, single head the two ends of the finished confirm the lamp holder as you the polarity of the two ends of the lamp connected wires, and then directly card directly into the lamp inside
Q:Fluorescent lamp double lamp tube wiring method
Is ok, if the electronic ballast, take a look at is a of the area, or area of two, if is one of the region, the four lines of the same light foot directly connected to the ballast end (the end of the four terminal) ballast directly connect the power cord is ok, on the other side of the ballast area 2, the light of the light feet a line connected to the ballast, on the other side of the ballast connect the power cord is ok!!
Q:What are the advantages and differences of the LED panel lights?
11.8 mm, the thinnest can do 8.5 mm, are light will be more than three times thicker than the side light, thin is a kind of fashion, especially for lifting the panel lights, also not the thinner the good, the thickness of the lamp body is designed according to the application environment and optical standards, guide plate with the thickness of the guide plate, the thickness of the lamp body with light body, too thin may influence the luminous efficiency of lamps and lanterns and optical and physical parameters, etc
Q:How does the lamp line connect
If it is converted by fluorescent lamp tube into LED lamp tube, want to remove the regenerator and the ballast. The two wires connected to A1 and A2 have been turned into a thread, and the two wires connecting B1 and B2 are also twisted into one line and are connected to the two ends of 220V respectively.
Q:If you want to replace it with an LED fluorescent tube, how many watts does it take?
Commonly used household generally is 1.2 meters, is a traditional fluorescent label 36 w, combined with the actual total power dissipation of the ballast at about 40 w. If replace with LED fluorescent tube, 18 w is enough light. Such as check brightness demand is not high, some useful also 16 w to replace.
We are a leading manufacturer of a broad range of LED strip light and LED Tube light. From 2011, we have integrating sphere spectrometer, high speed automatic placement machine, reflow soldering machine, automatic dispensing machines and other specialized equipment and professional R & D department. LED strip light can produce up to 300000 meters per month.

1. Manufacturer Overview

Location Shenzhen,China
Year Established 2011
Annual Output Value
Main Markets

Mid East;Western Europe
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Shenzhen
Export Percentage
No.of Employees in Trade Department 20 People
Language Spoken: Chinese
b)Factory Information  
Factory Size: Above 4,000 square meters
No. of Production Lines About 5
Contract Manufacturing OEM Service Offered;Design Service Offered
Product Price Range Cheap