LED Lighting T8 Integrated Light Tube CE RoHS TUV ETL t5 Bracket Lamp

Ref Price:
Loading Port:
Qingdao
Payment Terms:
TT OR LC
Min Order Qty:
1000 set
Supply Capability:
100000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

LED Lighting T8 Integrated Light Tube CE RoHS TUV ETL t5 Bracket Lamp Specification:


Material

Aluminium + PC cover

Body size

600mm

Light quantity

SMD2835/96Pcs

Power Installation

Power external in the tube

Work voltage

AC100-240V

Power consumption

10w

Power factor

>0.92

Work temperature

-20°C~+50°C

beam angle

120°

Color rendering

>80ra

Color temperature

2700-7200k

Luminous flux

950Lm

Light-to-Electric conversion yield

95%

Life span

50000hrs

Main Feature of LED Lighting T8 Integrated Light Tube CE RoHS TUV ETL t5 Bracket Lamp:

1.Magnetic&electronic ballast compatible

2.No need to remove starter or ballast.

3.No professional electrician needed 

4.Easy for installation

5.No labor cost,  maintenance free

6. instant start.

7. No UV, NO mecury, healthy for human body 

8.Power consumption:24w

9.Certificate:CE,RoHS,FCC,PSE,TUV,UL
10.Low power consumption
11.3 years warranty
10.No fluorescent flickering
11.No RF interference, no buzzing noise.
12.No hazard of mercury or lead entering the environment
13.Easy in stallation
14.No dangerous of glass broken

 

LED Lighting T8 Integrated Light Tube CE RoHS TUV ETL t5 Bracket Lamp Description:


1.Living room, bedroom,kitchen, washroom;


2.School, university, hospital,hotel;


3.Conference,meeting room, show room,showcase;


4.Commercial complexes;


5.Factory,plant,warehouse,office;


6.Supermarket,department store.

Images:

LED Lighting T8 Integrated Light Tube CE RoHS TUV ETL t5 Bracket Lamp

FAQ:

What certificates do you have for your products?

ISO



Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What is the difference between a radar sensor and an infrared LED fluorescent lamp?
Radar induction is radio frequency radio. Infrared sensing is infrared.I hope my answer is useful to you
Q:How many leds will be able to reach the 30W T8 lamp?
The fluorescent lamp is usually 45LM/W but half of the light is an invalid LED flashlight which is about 85LM/W.
Q:The reason for the slow start of an old-fashioned daylight tube
It is not easy to age and the lamp is aged.It seems to be connected to the seismograph.
Q:How to meet? The rectifier is very easy to connect
Went on two of the ballast with black and white and two sets of lines, a set of a tube, the last wire connects ballast is ok, if the change over time, to check whether a set of ballast to replace, so consider in ballast, if only a single change, that is about to change the bulb.
Q:How do fluorescent tubes clean
Use alcohol as a wipe.I hope my answer will help you
Q:How long does the energy-saving daylight lamp tube change?
Fluorescent lamp use time is long, the brightness is low is normal [because of the efficiency of fluorescent powder is reduced, cause lamp tube brightness drops]. The general store is not convenient to replace at any time, it is better to replace it at once. If you increase the density of the light, the light efficiency of the tube will not increase much, and the energy will increase with the opening of the tube, a little waste. A one-time change is a lot of input and a lot of it is compared to the actual computation.
Q:What about the normal daylight tubes replaced with LED tubes, ballast and flashers?
The rectifier usually has two types of inductance and electronic type: the direct short answer of inductance (one to one). The wire and the zero line of the electronic type (two in four) are short connected to the corresponding two sets of two lines, the regenerator is pulled directly, and the LED tube is installed.
Q:Can leds be used for a regular fluorescent lamp?
The starter down. When the regenerator was knocked down, my home was my own scissors and cut off the ends of the two ends of the regenerator. Then attach the severed head to the insulation tape. search Put the base back to the original. The head of the LED fluorescent tube will be plugged into the base current
Q:How to replace old lamp tubes with LED tubes
The leds that appear on the market today should be connected directly to the 220V power supply. The power supply and the lamp are together.
Q:Use LED fluorescent lamp tube to replace, the line of original daylight-tube seat should be refitted
Hello friend, I know you said of that kind of old-fashioned fluorescent lamp, there are two base, base on the inside are two elastic brass plates, you may be putting cover the outside of the plastic part of the brass screw is broken? It doesn't matter, just use your lamp plug contact on the brass base and bare department if you fear of insecurity is with insulation tape package no problem!

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range