LED Infrared Light T8 Tube 16W/3W Sensor Tube 1.2m

Ref Price:
$14.06 / pc
Loading Port:
Shenzhen
Payment Terms:
TT
Min Order Qty:
10 Pcs pc
Supply Capability:
100000 Pcs Per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

LED Infrared Light T8 Tube 16W/3W Sensor Tube 1.2m 1. This product meets the standard of CE certification.
2. With internal No-isolated power supply.
3. Round and the elliptical tube are available.
4. Use the most mature international well-known LEDSMD2866 as the light source, which can ensure the led tub35 as the light source, which can ensure the led tube brightness and long lifetime, also can reduce the light decay.
5. Use the high quality aluminum PCB for LED’s better heat dissipation.
6. High-grade PC cover with nice light transmittance(> 95%),Transparent PC cover and frosted PC cover are available.
7. 180 degrees beam angle makes the lighting effect better.
8. CRI(standard products)>70,it can be over 80 if required.
9. Ambient temperature:-20°C-40°C, surface temperature: 42°C-45°C
10. No mercury, lead or other hazardous materials; no radiation, no electromagnetic radiation, no frequency flash, instant start up, no hurting eyes.
Applications:
Replacement for conventional fluorescent tubes:
1. Hotels
2. Conference/ meeting room
3. Commercial Complexes
4. Residential/ Institution Buildings
5. Schools, colleges & Universities
6. Hospitals General li

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:The LED fluorescent lamp tube breaks the LED light in the inside
If this is not bad, then look back, there should be a small power supply at the end of the aluminum plate, and the other end of the power supply is 220V. Another possibility is that lower-end LED products will be blocked (non-isolated). Is the aluminum substrate in addition to the SMT chip, also some electronics posted above, if the aluminum board intact, you also to the end, one 220 v mains interface on both ends
Q:The various specifications of LED fluorescent tubes
LED daylight lamp tube routine parameters: 1, fluorescent lamp specifications: T8, T5, T4 difference and length of tubes, power description: commonly used with T8 and T5 fluorescent lamp specification, T4 lamp, with three tubes of a set of usually is T5 tube, commonly used fluorescent lamp specifications have T10, T12 long ago. "T", represents the "Tube", said the Tube, the Numbers behind the T Tube diameter, T8 is eight "T", a "T" is 1/8 of an inch, one inch is equal to 25.4 mm, then each of the "T" is 25.4 present 8 = 3.175 mm
Q:The lighting is replaced by LED lights and circuit problems
My home is a branch. The whole thing is broken even the base is changed, the base is to take the shock drill to drill in the wall, my home has no impact electric drill. The part of the branch is just changing the daylight lamp. Save trouble. The first time I took the regenerator and the ballast down, I had a makeover. You just need to put the fluorescent tube directly on it. Very simple.
Q:How does the traditional daylight lamp tube replace the LED light tube?
Please follow the instructions from the LED light tube manufacturer. Different manufacturers will be slightly different. You can only short-circuit the reactor that was built into the lampstand
Q:LED energy-saving integrated fluorescent lamp tube with four interconnections in the middle
Integration tube: currently, mainly appears in the LED industry, design reason mainly lies in the fact that the LED itself is not easy to damage, but the LED heat emitted by itself is very big, if the cooling area is too small, easy to cause the droop is bigger, so will the lamp and stents design together at the same time can reduce the cost, and can ensure the LED light attenuation!
Q:What is the idea of an LED daylight lamp called T5 or T8?
Integration tube: currently, mainly appears in the LED industry, design reason mainly lies in the fact that the LED itself is not easy to damage, but the LED heat emitted by itself is very big, if the cooling area is too small, easy to cause the droop is bigger, so will the lamp and stents design together at the same time can reduce the cost, and can ensure the LED light attenuation!
Q:The problem of LED lamp compatible ballast
Online are the so-called compatible led ballast, inside it is a constant current for high power led drive power supply, in order to adapt to a variety of different types of leds, it also has different output current varieties, also wants when buying according to the current to select the same current in the led lamp ballast compatible led, it with the ordinary led special-purpose ballast (is actually led a dedicated switch type constant current drive) is the difference on the power (which is the same kind of led do various tubes are common) is large, the range of output current of 300 ma compatible ballast, for example, it can automatically adapt to the current 300 ma from 9 w - any power between 25 w led bulb, but also has the smallest biggest range, the only requirement is that current to be the same.
Q:How does the LED fluorescent lamp tube be fixed with the aluminum plate in the tube?
I'd better draw it. It's not all riveting, for example, using glue to press the aluminum plate to the top
Q:What's the difference between a single input and a double-end input?
Like our products, single side used on special occasions, be flat installation place, double side is directly used in the traditional ordinary lamp, so change the LED fluorescent lamp is very convenient.
Q:What are the details of the whole process of the LED lamp?
When you do the rules, the key parts need you to provide some certificates, and you need to be careful with the suppliers
Focus on environmentally friendly LED intelligent lighting products are obtaining CE, ROHS, CCC and other domestic and international authoritative certification; product sales in the domestic market to maintain continuous growth, and exported to Europe, America, Southeast Asia more than 10 countries.

1. Manufacturer Overview

Location Shenzhen,China
Year Established 2011
Annual Output Value
Main Markets

Mid East;Western Europe
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Dongguan
Export Percentage
No.of Employees in Trade Department 50-100 People
Language Spoken: Chinese
b)Factory Information  
Factory Size: Above 1,500 square meters
No. of Production Lines About 5
Contract Manufacturing OEM Service Offered;Design Service Offered
Product Price Range Cheap