KQDL series vertical multi-stage single-suction centrifugal pump
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Product overview
KQD series multistage centrifugal pump is divided into KQDL vertical, KQDW horizontal multi-stage single export-oriented and KQDL vertical centrifugal pump, KQDW horizontal multi-stage export-oriented four more structure. Closer to the pump body of the new return pipe structure design, return pipe is not easy to damage, at the same time enhance the sealing of the pump. Instead of "O" ring rubber bellows mechanical seal is solved easily produce scale, jammed caused by mechanical seal leakage problem, quality is more reliable. Novel structure, superior quality; Running stability, avoid killed; Advanced design, save the investment; Unique parts and reduce the noise.
Application field
KQDL series multistage pump is my company according to the market need and development of series products, this product compared with similar products is small, the head difference between the same specification can be convenient for users to choose. This product is accord with GB/T 5657-5657 < < centrifugal pump technology conditions (Ⅲ) > > standard.
The working conditions
Speed: 1480/2950 r/min
Liquid: clean water or physical and chemical properties similar to water in the liquid.
Liquid temperature: 120 ℃ or less
Flow range: 3.7 ~ 200 m3 / h
Lift range: 12.1 ~ 240 m
The suction pressure of the maximum working pressure: maximum pressure 2.5 Mpa or less + pump
- Q:What is the dry running protector of screw pump? What's the principle and function? Thank you
- The utility model relates to a screw pump dry running protector, which is used for protecting the stator and the rotor of the screw pump from being transported by air
- Q:The function of centrifugal pump
- 4, bearings are set on the pump shaft supporting the pump shaft components, there are two kinds of rolling bearings and sliding bearings. Rolling bearings use butter as a lubricant, refueling should be appropriate, generally 2/3 ~ 3/4 of the volume is too much, will heat, too little, there is noise and fever! The plain bearings are made of transparent oil as a lubricant and fill up to the oil level. Too much oil will leak out along the pump shaft and float *, too little, the bearings will overheat and burn out, causing accidents! In the pump running process, bearing temperature is highest in 85 degrees, generally run at about 60 degrees, if higher, will find the reason (whether there is impurities, whether the oil is black, whether water) and timely processing!
- Q:What does electromechanical vector pump mean?
- It is a close set of mechanical and microelectronic technology. It adopts dual control center mode to control, and has a new water pump with logic control center and IPC control center.
- Q:I live on the 8 floor. Often there is no water. Life is very inconvenient. What kind of pump do I have to install? What should I pay attention to when I buy it? What's the pump for that brand? Should it be installed in that position?
- (8) check the suitability of the foundation and whether the size of the foundation corresponds to the size of the pump.(9) find the position of positive pump and motor, pump set and anchor bolt and the inlet and outlet flanges, to ensure that the flange torque of the pump conforms to the standard. Check the inlet and outlet piping before alignment. Make sure the weight of the inlet and outlet pipe does not exert force or torque on the pump. When looking for, should also pay attention to eliminate the pump rotor movement, so as to avoid the end gap error. If checked after the pump is working, it should be carried out under cold condition. It is important to draw attention to the fact that the pump set of the complete set of factory is only rough looking (checked with a ruler) when it is shipped. It may cause displacement when it is transported.
- Q:How to calculate the motor power of metering pump?
- The total mechanical power and hydraulic power, divided by the overall efficiency of pump, and the pump head and the utilization rate of pump mechanical efficiency, and then multiplied by 1.1 times (API675), you can get a metering pump motor need more power.
- Q:What are the main performance parameters of hydraulic pumps?
- speedOperating speed is the actual rotation speed of a pump (or motor) at work.Rated speed is the maximum speed that can operate normally for a long time under rated pressure. If the pump exceeds the rated speed, the work will cause insufficient oil absorption, vibration and noise, the parts will suffer cavitation damage, life expectancy.Minimum steady speed is the minimum speed allowed for normal motor operation. At this speed, the motor does not appear crawling phenomenon.
- Q:Harm of air pump and pump
- If the liquid is not full, this situation is generally the suction pipe or pump shell leakage, then easy to cause cavitationHit the pump for centrifugal pumps, centrifugal pump is recommended to start closed, the discharge valve closed, starting is in the state of pump
- Q:Common failure treatment of piston pump
- x09x09 (3) no connecting key on pump shaft or motor shaft1) break2) missing x091) replace key2) patch keyx09x09 (4) pump internal slide vice stuck1) the clearance is too small2) parts accuracy is poor, assembly quality is poor, gear and shaft coaxial deviation is too large; plunger head clamping; blade perpendicularity difference; rotor pendulum difference is too big, rotor slot has wound or blade has scar, force after fracture and stuck
- Q:What are the conditions required for hydraulic pumps to complete oil absorption and compression?
- 2, the change of working volume is periodic, and in each cycle, the oil absorption process is changed from small to big, and the process of oil pressure is changed from large to small;3, suction oil cavity must be separated from each other without interference.
- Q:What is the liquid pump? What are their categories? What are their strengths and weaknesses?
- The liquid pump can be filled with oil, water and chemical medium. The gas drive range of the liquid pump is 1 to 10bar (14.5-145psi). The bottom piston is controlled by a two position four pass pilot valve.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
KQDL series vertical multi-stage single-suction centrifugal pump
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords