knife seat,F-KB042 Rubber wood knife seat,your best choice

Ref Price:
Loading Port:
Guangzhou
Payment Terms:
TT OR LC
Min Order Qty:
1000 pc
Supply Capability:
100000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

product name:rubber wood knife seat

material:rubber wood

N.W.:1.64kg

MEAS:22*14.5*11.5cm



Specifications:

Has the quite distinct shape of the mountain wood grain, and the contact surface is a good sense

Excellent toughness, process into various curved according to the needs , full of beauty

Solid texture,manufactured goods with firm structure,prolonged service life

The texture of rubber wood is fine and closely woven,pore full of lots ot padding so it's hard to absorb water and corrode.


Description:

1、The knife seat use material of high quality natural rubber wood and take professional advanced machine equipment and manual binding.

2、The knife seat was refined by material, assembly, polishing, painting and other procedures.

3、The knife holder has the advantages of real materials, excellent workmanship, mouldproof and moth proofing, anti bacteria, wear-resisting etc.

4、Hoteam commerce co.,LTD,is a manufactory specialized in all kinds of wood knife handles,wood seats,chopping boards and other woodworks.

5、Because the knife tool contact with tool wet food for long time, is very easy to breed bacteria, you should ensure  that  dry and clean and put it in the open air



Primary Competitive Advantages:

Brand-name Parts                   Country of Origin

Distributorships Offered           Experienced Staff

Form A                             Green Product

Guarantee/Warranty                 International Approvals

Packaging                          Price

Product Features                   Product Performance

Prompt Delivery


Main Export Markets:

Eastern Europe                     North America

Mid East/Africa                    Central/South America

Asia                               Western Europe

Australasia


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What are the parts of the lathe and tool holder
A lathe is a device; a tool holder is a lathe.
Q:Why use the center and the rest?
When machining slender shafts, use the center frame and the tool holder for the following reasons:First, the use of the central support of the vehicle shaft1, the central frame is directly supported in the middle of the workpiece when the workpiece can be segmented, the center of the support in the middle of the workpiece, so that the support, L/d value reduced by half, slender shaft turning rigidity can be increased several times. Before the work piece is installed on the center frame, it must be in the middle part of the blank to produce a part of the support of the central support of the groove, the surface roughness and cylindricity error is small, otherwise it will affect the accuracy of the workpiece.Two, the use of the tool holder with the support of the fine axisWith the tool holder fixed on the bed saddle, there are generally two supporting claws, with the tool holder can follow the movement of the tool to offset radial cutting can increase the stiffness of the workpiece, reduce deformation. So as to improve the shape precision and reduce the surface roughness.According to the design principle of the tool holder, only two supporting claws can be used, because the cutting resistance of the lathe tool to the workpiece is F`r, the workpiece is stuck on the two supporting claws of the tool rest. But in actual use, the workpiece itself has a downward gravity, and bending workpiece inevitably therefore, when turning the workpiece, often due to centrifugal force instantaneous left supporting claw, a supporting claw contact vibration. If the three supporting claws are used to support the workpiece, the workpiece is supported by a lathe tool, so that the upper and the lower parts of the workpiece can not move, and the turning is stable, and the vibration is not easy to generate. Therefore, when the car is fine to find a very critical problem is to use the shaft with three claws.
Q:The cutting surface of the optical fiber cutter is like this, what's going on?
Adjustable knife before, to ensure that the four fiber laminated pad is clean, no deformation, shaft bearing is normal; then the first turn, all faces turn over, go a little bit higher tone. If you do not know the chaos, the first transfer can not be cut, and then slowly to a little bit up. The key is to check the fiber laminated pad and tool, or how to adjust is in vain. In addition, the quality of the blade is also related to some of the poor quality of the blade is lower than the hardness of silicon dioxide, it is difficult to cut, how to tune useless.
Q:How to maintain the lathe tool holder
If the positioning and clamping action is normal, the push rod 11 is in contact with the corresponding contact 12, and the signal is sent to indicate that the tool changing process has ended, and the cutting process can be carried out.In addition to the positioning of the hydraulic cylinder and the positioning pin, the motor can also be used to drive the clutch to locate, as well as other indexing and positioning mechanisms.
Q:What is the difference between the KSJ and HV
Far, the accuracy of the KSJ knife, the quality is much higher than the HV, the price in that bad! But I'm talking about genuine
Q:What is the difference between the NC lathe and the tool post
X direction is not the same, when cutting the spindle is not the same! And then explore their own, basically so
Q:GSK980TA CNC lathe tool holder how to move
Hand hold tool motor, and then press the knife, I feel that there is no motor movements. 1, if the turret motor does not act, it should be a circuit problem, please check whether or not the work of the holder of the relay, the power supply is not normal, etc.. 2, if there has been support motor action and feeling in the action, that should be a tool of mechanical failure, please rest on the lower left one screw off with six angle wrench tool to see whether the worm shaft can rotate the turret rotation if it will rest to 45 degrees and then try to change the knife, if not to move it please remove the knife. 3, if the knife motor action and click No action, it may be broken or the knife knife signal line transmitting disk bad.
Q:How do you know how to install the roller skates?
Skating shoe body base generally has several fixing holes to make you bolt between the knife holder and the shoe body is no gap and then hand swinging knife without shaking the OK but then skate like Michael u and H HV of the black flag, such as shoes, you don't need to remove what their knife rack not what the problem is often removed but will reduce the life of tool it is a general method of alloy steel on it is invalid so don't worry about bold play is. I wish you good luck
Q:Why is the number 980 CNC lathe turret always turn and then alarm
Tool holder is always unable to find the knife position, usually 24 or 0 volts knife restIf it is a station can not find the detection switch is broken
Q:What are the advantages and disadvantages of CNC lathe turret
Tool holder is a very important part of CNC lathe. The structure form of the general lathe for rotary cutter is mounted on the carriage along the circumferential direction, radial and axial turning tools can be installed, drilling and boring. The machining center can also be equipped with an axial milling cutter and a radial milling cutter. A small number of CNC lathe tool holder for the straight row type, cutting tool installed along a straight line.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range