knife seat,F-KB087 Carbonized bamboo knife seat,your best choice

Ref Price:
Loading Port:
Guangzhou
Payment Terms:
TT OR LC
Min Order Qty:
1000 pc
Supply Capability:
100000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

product name:rubber wood knife seat

material:rubber wood

N.W.:0.568kg

MEAS:24.5*22.11cm


Product advantage:

How does the bamboo product carbonize?Firstly,put the bamboo or bamboo bag into the high-pressure carbonized boiler of 200 degrees - 300 degrees for vapor carbonization,and after high temperature and high pressure, so that form a hard carbide particles layer on the surface.At the same time,the bamboo itself will be more harder.


The advantage of carbonized bamboo knife seat:after carbonize,hard carbide particles  will form a environment not easy living for bacteria on the surface of bamboo product to achieve the antibacterial effect.At the same time, because after carbonization the bamboo will be more hard than ordinary paper products,  preventing wearing and bamboo thorn problem.


Carbonized bamboo knife seat quantity:

Safety, health, bright color,durable,the everyday necessary good products

Anti-mildew change,anti moth

Environmental protection,no crack,no decay


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What is the cause of the shaking of the turret
Spend some money, from bending machine manufacturers please a teacher to do.
Q:There is no difference between the tool holder and the tool holder
The turret of the numerical control lathe is the front knife holder in the operator's side.The common lathe is the rear cutter.When the tool head, the G42 tip radius compensation right bias in the car when the hole, when the car is round with G41.
Q:What is the difference between the NC lathe and the tool post
The opposite direction of arc G02/03 rotation, the rest are the same
Q:How to install CNC machine tool
Side frame installation(1) remove the strip, the pressure plate, cleaning the guide rail and other processing surface, check the defect and put on the lubricating oil.(2) the connecting piece of the tool holder and the counterweight, such as the bearing, the pulley (or the chain wheel), the axle, the hanging rope or the chain, and so on.(3) the stone school F on the positive exploration in wood, clean school guide surface, with lubricating oil, the side head hanging on it, slowly close to the school with positive guide, strip, plate, preliminary adjustment guide clearance, connection lifting mechanism.(4) connect the counterweight and the side of the turret, rose hand operation knife, check whether there is blocked, demolition of timbers.
Q:The cutting surface of the optical fiber cutter is like this, what's going on?
I do not know if you are in the optical fiber welding machine is not the Japanese cutter, Sumitomo, whether or not, a knife can only be cut 6000 times, Sumitomo is considered good. Generally buy the welding machine with a knife. If you don't, you can only go back to one, because if you cut it off, you can only prove that it's not working. Is disposable. Only changing one, should not be expensive, you want to, you can't cut a few times, so that the fiber section is not smooth. In this way, the welding of the fiber as if it is not very high quality. Generally a good knife, cut out of the surface is smooth and smooth. In this way, the general quality of the fiber is relatively high. Can only change, repair, then bad repair!
Q:Why do you want to use the center frame and the tool holder when machining the slender shaft?
Because, when processing the slender shaft, the process system rigidity problems, mainly for the slender shaft rigidity is low, the cutting force (radial force) under the action of bending deformation (elastic deformation), car axle, a middle drum. The center frame or the tool holder is used to counteract the radial cutting force and increase the rigidity of the slender shaft.
Q:The difference between the tool holder and the electric tool holder
The difference is that there is only one knife library, is T0101, if you want to use a few knives, that is, 02 or more behind the T01 can do it!To row knife knife, if you want to T0101 the knife, you put a knife to a knife or light near the end, directly in the 01 hit patch which according to the Z0 input, the outer circle you have, what is the volume of just the tool compensation which according to the X.. Input, you want to second third or more knife is the same; but you must take the time to fill in to lose in the digital knife to a knife, or otherwise useless.The tool holder is four knife library, you want to use a knife is T0101 or T0202.T0303.T0404. The two is not mixed with the. Hope to help you.
Q:What is the function of the tool on the turret of NC lathe?
The angle of the adjusting tool post is only temporary change, and the position of the tool post can be repeatedly positioned after the rotation of the tool holder!
Q:Why is the number 980 CNC lathe turret always turn and then alarm
Tool holder is always unable to find the knife position, usually 24 or 0 volts knife restIf it is a station can not find the detection switch is broken
Q:What are the parts of the lathe and tool holder
A lathe is a machine with many parts assembled.A part of a lathe.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range