knife seat,F-KB031 Rubber wood knife seat,your best choice

Ref Price:
Loading Port:
Guangzhou
Payment Terms:
TT OR LC
Min Order Qty:
1000 pc
Supply Capability:
100000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

product name:rubber wood knife seat

material:rubber wood

N.W.:1.35kg

MEAS:22*19*10cm



Specifications:

Has the quite distinct shape of the mountain wood grain, and the contact surface is a good sense

Excellent toughness, process into various curved according to the needs , full of beauty

Solid texture,manufactured goods with firm structure,prolonged service life

The texture of rubber wood is fine and closely woven,pore full of lots ot padding so it's hard to absorb water and corrode.


Description:

1、The knife seat use material of high quality natural rubber wood and take professional advanced machine equipment and manual binding.

2、The knife seat was refined by material, assembly, polishing, painting and other procedures.

3、The knife holder has the advantages of real materials, excellent workmanship, mouldproof and moth proofing, anti bacteria, wear-resisting etc.

4、Hoteam commerce co.,LTD,is a manufactory specialized in all kinds of wood knife handles,wood seats,chopping boards and other woodworks.

5、Because the knife tool contact with tool wet food for long time, is very easy to breed bacteria, you should ensure  that  dry and clean and put it in the open air


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:CNC vertical lathe tool holder
In the tip of the compensation bar to enter the radius of the tip of the knife is good, of course, we must first know the radius of the tip of the nose,
Q:The rotary tool holder is marked with the knife number. How to define the knife number?
There is no knife in the actual sense of the knife number, because it is to use the knife to determine the use of the.
Q:Why use the center and the rest?
When machining slender shafts, use the center frame and the tool holder for the following reasons:First, the use of the central support of the vehicle shaft1, the central frame is directly supported in the middle of the workpiece when the workpiece can be segmented, the center of the support in the middle of the workpiece, so that the support, L/d value reduced by half, slender shaft turning rigidity can be increased several times. Before the work piece is installed on the center frame, it must be in the middle part of the blank to produce a part of the support of the central support of the groove, the surface roughness and cylindricity error is small, otherwise it will affect the accuracy of the workpiece.Two, the use of the tool holder with the support of the fine axisWith the tool holder fixed on the bed saddle, there are generally two supporting claws, with the tool holder can follow the movement of the tool to offset radial cutting can increase the stiffness of the workpiece, reduce deformation. So as to improve the shape precision and reduce the surface roughness.According to the design principle of the tool holder, only two supporting claws can be used, because the cutting resistance of the lathe tool to the workpiece is F`r, the workpiece is stuck on the two supporting claws of the tool rest. But in actual use, the workpiece itself has a downward gravity, and bending workpiece inevitably therefore, when turning the workpiece, often due to centrifugal force instantaneous left supporting claw, a supporting claw contact vibration. If the three supporting claws are used to support the workpiece, the workpiece is supported by a lathe tool, so that the upper and the lower parts of the workpiece can not move, and the turning is stable, and the vibration is not easy to generate. Therefore, when the car is fine to find a very critical problem is to use the shaft with three claws.
Q:Numerical control lathe tool holder is a tool to change what is the fault
See what aspects of the problem, is the electrical problem, or mechanical problems, electrical problems, is the location of the magnetic switch to run, or the signal line is short. The mechanical problem is not in place, the first point of lubrication to see if it is caused by dry. If it is not, it is necessary to open the knife
Q:What is the reason why the turret of NC lathe is not maintained?
May rest inside the lines are wrong, may also have a lid on the knife frame out
Q:How to do the tool holder of the NC turret with too long time
It is likely to be stuck inside the knife, first give it a break, and then pour some oil inside
Q:The structure and working principle of 4 position tool holder
This thing to have a picture to explain, the text can not express. Remove the countless times, the rotation of the motor makes the knife rises and then rotating, on top of a Hall element to detect the Holland tool you need is not to, to the motor reversal, falling knife stuck in the tooth is motor locked dead. There is a spring in the middle of the shaft and drives the two clips to play a key role. A lot of reasons for the death of the tool holder are caused by the broken line in the middle.
Q:What is the tool rest
Auxiliary device for rotating workpiece with radial support. During machining, the workpiece moves axially along with the tool.
Q:CNC lathe tool holder clamping bit how to clip
If it is a square knife, just to make a fixture, clamping on the tool holder, tooling with Morse 4# internal cone, the inner cone can be fitted with a drill chuck, can also be directly fitted with taper shank drill.
Q:The electric turret is installed on the tool rest in the lathe bed
It seems that the tail frame can not be installed, loaded up is not much significance other can be installed at least 120 thousand or more

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range