knife seat,F-KB012 acacia wood knife seat,your best choice

Ref Price:
Loading Port:
Guangzhou
Payment Terms:
TT OR LC
Min Order Qty:
1000 pc
Supply Capability:
100000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

product name:acacia wood knife seat

material:acacia wood

N.W.:2.23kg

MEAS:28*19.5*17cm


Specifications:

Has the quite distinct shape of the mountain wood grain, and the contact surface is a good sense

Excellent toughness, process into various curved according to the needs , full of beauty

Solid texture,manufactured goods with firm structure,prolonged service life

The texture of rubber wood is fine and closely woven,pore full of lots ot padding so it's hard to absorb water and corrode.


acacia wood knife seat quantity:

Safety, health, bright color,durable,the everyday necessary good products

Anti-mildew change,anti moth

Environmental protection,no crack,no decay


Primary Competitive Advantages:

Brand-name Parts                   Country of Origin

Distributorships Offered           Experienced Staff

Form A                             Green Product

Guarantee/Warranty                 International Approvals

Packaging                          Price

Product Features                   Product Performance

Prompt Delivery


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Numerical control lathe tool holder is a tool to change what is the fault
It should have been broken. It's the white plastic ring. Seems to forget what
Q:Numerical control four station tool holder has been unable to stop what reason?
Holzer component position (open the top cover can be seen as commonly referred to as the disk) is not right or damaged. Has not been able to stop because of the knife can not find the signal in place 4.
Q:How to return to the ordinary lathe tool
Remove and check whether the spring pin back position is smooth (with the hands of the press about 20 times). Take a look at whether the end of the spring pin has been seriously worn, the same knife bottom surface is also turned over to see if the limit groove is also serious wear.
Q:Where are the Holzer elements in the CNC turret?
A cutter position corresponds to a Holzer element, usually enclosed in a round plastic box
Q:CNC lathe tool holder four and six stations which good
The internal structure of the turret principle is similar, but the four station looks like car carriage, six station is a brick tower structure, slightly larger, a fixture of processing content more, six station processing large size parts, the adjacent knife knife may interfere with the four station, six station four station your. Think about it.
Q:CNC lathe tool holder can not be reset after the knife to do?
If you are unable to move the carriage to exit a and then try to use it to turn off the power first hand, or if not it may be burned (IF amplifier module in the boot state can rotate with hand screw it must be.). Look for an electrician, do not have to change the words.
Q:The lathe tool holder is always turning, unable to reach the designated position
I have encountered such a problem, the circuit has a capacitor breakdown, check the replacement can be.
Q:Advantages and disadvantages of drift plate holder and S frame
Vertical typeThe wheel frame, in fact, is a parallel steel frame structure.Than S, there are many advantages.For example, solid, DIY, modification, etc.
Q:How to distinguish the front tool holder and the tool post
Whether NC or normal car, a knife in the side is the pre processor, or post, either rear or front, when processing with radius compensation are determined according to the post, the outer circle with G42, G41 in the hole.
Q:What are the parts of the lathe and tool holder
A lathe is a device; a tool holder is a lathe.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range