knife seat,F-KB010 acacia wood knife seat,your best choice

Ref Price:
Loading Port:
Guangzhou
Payment Terms:
TT OR LC
Min Order Qty:
1000 pc
Supply Capability:
100000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

product name:acacia wood knife seat

material:acacia wood

N.W.:1.204kg

MEAS:23*19.5*6cm


Specifications:

Has the quite distinct shape of the mountain wood grain, and the contact surface is a good sense

Excellent toughness, process into various curved according to the needs , full of beauty

Solid texture,manufactured goods with firm structure,prolonged service life

The texture of rubber wood is fine and closely woven,pore full of lots ot padding so it's hard to absorb water and corrode.


Description:

1、The knife seat use material of high quality natural acacia wood and take professional advanced machine equipment and manual binding.

2、The knife seat was refined by material, assembly, polishing, painting and other procedures.

3、The knife holder has the advantages of real materials, excellent workmanship, mouldproof and moth proofing, anti bacteria, wear-resisting etc.

4、Hoteam commerce co.,LTD,is a manufactory specialized in all kinds of wood knife handles,wood seats,chopping boards and other woodworks.

5、Because the knife tool contact with tool wet food for long time, is very easy to breed bacteria, you should ensure  that  dry and clean and put it in the open air


acacia wood knife seat quantity:

Safety, health, bright color,durable,the everyday necessary good products

Anti-mildew change,anti moth

Environmental protection,no crack,no decay


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Why do you want to use the center frame and the tool holder when machining the slender shaft?
Because, when processing the slender shaft, the process system rigidity problems, mainly for the slender shaft rigidity is low, the cutting force (radial force) under the action of bending deformation (elastic deformation), car axle, a middle drum. The center frame or the tool holder is used to counteract the radial cutting force and increase the rigidity of the slender shaft.
Q:The direction of the tool head and the tool head of the NC lathe
G41g42 use the judgment of the tool tip is not the same as you this figure to 09 knife point for the center of the rotation of 180 degrees is the rear tool head position input value evaluation standard front and rear is the same as the input value
Q:The structure and working principle of 4 position tool holder
4 position tool holder structure of numerical control vehicle:Under normal circumstances can be fitted with 4 knives, the knife holder inside a worm with a turbineThe knife and the base on the contact surface of one end gear and two limiting block, the upper surface of the base two end face gear engaged normally a motor and worm shaft.The principle of 4 station tool holder for NC lathe:The knife is receiving the instructions in the form of pulse waves, when receiving a tool change instruction motor drives the turbine and worm. The worm to rotate the cutter knife up end gear separation, when the turret is elevated to a certain extent, together with the turret turret rotation worm together, rotate 90 degrees after encountering a limit block, because the motor power is blocked to when starting to reverse, the natural turret decline on the base end gear limit block lock, complete tool change
Q:What is the difference between the KSJ and HV
Far, the accuracy of the KSJ knife, the quality is much higher than the HV, the price in that bad! But I'm talking about genuine
Q:What is the cause of the shaking of the turret
Look at the oil tank is not dirty or oil is not enough to clean the oil tank filter, there may be poor oil absorption.
Q:Advantages and disadvantages of drift plate holder and S frame
Modified DIY it certainly is h good, can change the surface of bamboo wood aluminum can, spray painting stickers can... The support of the s arm than the low end of the non uniform force... The actual s arm didn't what reinforced technology, the most vulnerable to bad is that even if you part of aluminum, steel shaft intact, aluminum bent??? From the point of view of the wheel easy disassembly, s frame is much better, less two outer shaft on the convenience. As for the slide is more dependent on the wheels and bearings, s frame is close to the center of gravity of the Double Tour dragon board, h's center of gravity close to the long plate in the skateboard, of course, the difference is not so big, more difficult than the long board.
Q:CNC turret is also called the sender sensor
No, the inductive switch is only one of the components of the sender. Each unit corresponds to a Holzer sensor, along with the knife on the knife body rotation, the switch will be close to the magnet Holzer signal. What is the location of the knife to tell the host. The white piece fixed on the edge is a magnet. The middle line is the sensor. Together, they constitute a communications disk.
Q:What is the difference between NC machine tool and tool holder
In front of the turret with rear turret X axis is not the same, the general system programming does not have what difference, the front turret program got rear turret lathe bed on the same processing, but also have different, like Beijing DTM window system, front and rear arc knife tool that is just the opposite.
Q:What are the advantages and disadvantages of CNC lathe turret
CNC lathe in the use of the process, the common fault of the tool holder, spindle, thread processing class, the system display class, drive class, communications and other failures, and the tool holder fault occupies a large proportion. After the failure of the machine can not be used temporarily, resulting in a waste of manpower and material resources in time. If we can do some basic maintenance, we can save costs, save time and create a certain economic benefits.
Q:The difference between the turret and the rear turret NC lathe
The classification processing example scope advantages and disadvantages of different composition of 2.3 ordinary lathe and CNC lathe CNC lathe uses a directory of the two introduction 2.1 CNC lathe 2.2 CNC lathe 2.4 CNC lathe 2.5 CNC lathe CNC lathe CNC lathe 2.6 three 3.1 NC turning process and tooling 3.2 CNC lathe programming 3.3 part four references

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range