Knife Gate Valve With Gear Operator

Ref Price:
Loading Port:
China Main Port
Payment Terms:
Min Order Qty:
Supply Capability:

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:



Pressure:PN10, PN16


Body:cast iron, ductile iron, stainless steel

Disc: stainless steel, WCB

Stem: stainless steel

Seal: rubber, teflon, stainless steel, etc.

These products are widely used in water source projects,urban water  supply and drainage, sewage treatment, papermaking, coal mine, heat supply, petroleum, petrochemical,etc.
Suitable for manual, bevel gear, pneumatic, electric, etc.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What is the difference between gate valves Z41W-16R and Z41W-16P?
According to JB/T308P stands for Cr-Ni stainless steelR stands for Cr-Ni-Mo stainless steelCr-Ni stainless acid resistant steel has CF8, CF3, F304, F304L, which applies to the medium of work, such as nitric acid oxidation acid.Cr-Ni-Mo stainless acid resistant steel has CF8M, CF3M, F316 and F316L, which is suitable for working medium, such as acetic acid and reducing acid.
Q:What are the differences between the gate valve and the cut-off valve?
3, the valve is used in the system is relatively large, to close the gate off system; and the valve is used in the system is relatively small, and to adjust the flow quantity of the system, can not be closed gate and globe valves of different specifications for a variety of occasions, such as the valve rod the dark bar valve, gate valve, wedge gate valve, single valve, multi valve valve body structure is different, large volume. Generally large and nominal caliber DN50 mostly with gate valve, especially industrial high temperature, high pressure and other occasions.4, the cut-off valve is able to stop and adjust the flow, small footprint, small size, generally less than the nominal diameter, DN50 occasions use it. Two can be closed, in the flow of linear requirements are not high, you can adjust the flow. Just because of its structural characteristics of the valve to make its flow resistance, so there is a demand for throttling with a little more than the gate valve. In addition, the cut-off valve, whether it is a formal or reverse installed, in the opening and closing process, there is always a very difficult, and therefore can not do a great deal, or it is not easy to open and close. In addition, the sealing valve has the characteristics of one-way sealing effect, so that the utility model can prevent the working substance from flowing upstream
Q:About fire valve is gate valve or butterfly valve problems?
Disease is generally in accordance with the design requirements, regardless of the butterfly or tie hair to meet the requirements, are two-way valve.
Q:What type of flange does it fit with the gate valve?
According to the welding plate flange, flange material selection of piping material.
Q:What is the wedge type gate valve wedge is what mean
According to the gate can be divided into the form of parallel wedge type. (1) wedge type gate. Wedge type gate the sealing surface of a certain angle with the vertical center line of the gate, the size of angle depends on the medium temperature and diameter size. General medium temperature is higher, and the greater the inclination angle is bigger, in order to prevent the temperature change when the gate is stuck, unable to open. Wedge gate sealing than the parallel well.
Q:What is the difference between the cut-off valve and the gate valve?
What is the difference between gate valve and stop valve?:Gate valve and globe valve structure is different, the valve structure for hand wheel, with the stem rotating together to do the opening and closing movement. Valve structure is rotating handwheel, stem do lifting movement. The flow is different, the gate valve requires full open or full closed state, the cut-off valve does not need. The valve has the flow direction requirements, and the gate valve has no inlet and outlet requirements!Sealing performance comparison:Valve length is shorter than the cut-off valve, higher than the cut-off valve, the valve should pay attention to the installation of high elevation. The gate valve can be tightly closed with the sealing surface by the pressure of the medium so as to achieve the effect of not leaking.
Q:What are the working principles of the electric gate valve?
We see you what type of electric valve, is integral or ordinary type, if the overall type Denso took power on the line, is generally 380V and 220V power supply, and then according to their own needs and then open the signal line, in place and closing in place and remote control line, valve position feedback signal the commonly used 4~20ma over torque protection fault signal.
Q:Notes on flat gate valves
Use, maintenance, maintenance and precautions1. valve before leaving the factory have made strength and sealing test, the use of all connections should maintain the initial state.2. this series of valve operating handwheel is marked with open and close rotary direction, and the upper part of rod is equipped with open and close height gauge for regulating indication.3. when the valve and pipeline welding, the valve should be opened, appropriate to protect the neck with moisture, minimize heat conduction, to prevent damage to the sealing packing parts.4. when the valve is closed, the lever shall not be used. When the gate is closed to the top, the handwheel shall be turned 1/2 so that the gate is in a floating state.5. in the use of the valve should be regularly to the valve cap injection grease joint into the quantitative grease.6., the valve in use, such as vulnerable parts and leakage, should be replaced in time.7., the valve in the overhaul process, the cavity should be cleaned, the assembly should be added to the transmission parts of grease.8. valve storage during the shutdown, the gate should be in the closed position, long-term storage should be placed in ventilated dry place, regular inspection and maintenance.
Q:What does "Z45W-10T" mean?What does each letter stand for?
T is the material code for the valve body, which stands for copper and copper alloysZ45W-10T, which means manual, flange connections, dark wedge rigid single gate plate, the valve seat sealing surface material directly processed by the valve body, nominal pressure PN10, valve body material for Brass Gate Valve
Q:What is the Z15T-16C letter of the gate valve?
The Z class code indicates the type of gate valve, gate valve is the first letter of the alphabet. The gate is manual driving mode, 1 said the connection form of gate valve for connecting thread, 5 represents the structure form of gate valve for rigid single gate, T gate said lining material of copper alloy, 16 PN1.6MPa nominal pressure valve. C said the valve body material is carbon steel.

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range