Q:What material does the power tool housing fit?

Electric drill: the main specifications are 4, 6, 8, 10, 13, 16, 19, 23, 32, 38, 49mm and so on. The figures refer to the steel whose tensile strength is 390N/mmThe maximum diameter of a drill drilled on a material. For non-ferrous metals, plastics and other materials, the maximum drilling diameter is comparable to the original specifications of 30 to 50%.Electric grinding machine: a tool for grinding with a grinding wheel or millstone. A vertical electric wheel and electric angle grinder.Electric wrench and electric screwdriver: used for loading and unloading threaded fittings. The driving mechanism of the electric wrench is composed of a planetary gear and a ball screw groove impact mechanism. Specifications are M8, M12, M16, M20, M24, M30 and so on. An electric screwdriver adopts a clutch, a transmission mechanism, or a gear drive mechanismThere are M1, M2, M3, M4, M6 and so on.

Q:What other tools are there for the furniture except the pistol hole?

As we all know, a hand drill is an AC power supply or a DC battery powered drilling tool. It is a kind of hand held power tool.

Q:Which is good between pneumatic tools and power tools?

Pneumatic tools are the mainstream trend, pneumatic tools more suitable for long time work, rather than power tools, permanent fever, and even burned out the internal parts, pneumatic tools can be seen more secure. Power tools initial investment is low, but long-term use of energy consumption is higher, and tool maintenance and replacement costs are higher, and pneumatic tools more environmentally friendly, long-term use cost is much lower than the electric.

Q:What kind of power tools are hand drills? 1, 2 or 3?

You can see the cable plug, the aluminum shell is inserted three I tools, is grounded, the aluminum shell and some II tools, because it has a plastic insulation between the stator and the aluminum shell, so it is the installation of two wire plug.

Q:What devices must be available for all hand held electric tools?

Anti leakage, splash prevention, anti movement, anti overheating

Q:Compared to pneumatic tools, what are the advantages of electric tools?

At the same time, reversing operation, pneumatic tools, small size, high speed rotary speed, easy to adjust, no danger of fire, the air compressor can also be used in the house, is the best choice for sheet metal, paint, furniture manufacturing, auto hub processing, etc..

Q:How are hand powered tools classified into class I, class II, class III?

Class I protection against shock of the product depends not only on the basic insulation of the equipment, but also on additional safety precautions. The method is to connect the electrically conductive parts that may be touched with the protective wires in the installed stationary lines so that the accessible, electrically conductive parts are not electrified in the event of basic insulation damage. Such products are: hand-held power tools, mobile daily appliances, mobile mechanical and electrical equipment.

Q:What's the difference between a flashlight and an electric screwdriver?

A flashlight is a drilling tool powered by alternating current or direct current batteries. It is a hand-held electric tool.The main components of a drill are a drill chuck, an output shaft, a gear, a rotor, a stator, a casing, a switch and a cable.Electric torch (pistol drill) -- a tool used for drilling metal, wood, plastics, etc.. When equipped with positive and negative reverse switch and electronic speed regulating device, it can be used as electric screwdriver. Some models are equipped with rechargeable batteries, which can work normally within a certain period of time without external power supply.

Q:What are the commonly used rotor types for power tools?

Electric drill: the main specifications are 4, 6, 8, 10, 16, 19, 23, 25, 32, 38, 13, 49mm and so on. Figures refer to the maximum diameter of the drill drilled on the steel whose tensile strength is 390N/mm. For non-ferrous metals, plastics and other materials, the maximum drilling diameter is comparable to the original specifications of 30 to 50%.Electric grinding machine: a tool for grinding with a grinding wheel or millstone. A vertical electric wheel and electric angle grinder.Electric wrench and electric screwdriver: used for loading and unloading threaded fittings. The driving mechanism of the electric wrench is composed of a planetary gear and a ball screw groove impact mechanism. Specifications are M8, M12, M16, M20, M24, M30 and so on. The electric screwdriver adopts the embedded clutch, transmission mechanism or gear drive mechanism. The specifications include M1, M2, M3, M4, M6 and so on.The hammer and drill: used for concrete, brick and building components on drilling, slotting, dehairing. With expansion bolts, installation can improve the speed and quality of pipeline, machine equipment; impact hammer principle is to rely on the internal movement of the piston impact force, impact principle of impact drill is running in gear impact force, so the impact hammer is greater.

Q:What is the working principle of power tools?

AC motor, AC motor of induction motor, its strong induction current (eddy current) magnetic field generated in the rotation of the magnetic force on the rotor copper bar, continuous cutting, according to Lenz's law, the induced current has the effect of relative motion occurs against the rotor magnetic field and the rotor is, with the magnetic field and rotation. But the rotor rotation speed of the high speed magnetic field does not transform, otherwise it will not be able to cut the copper lines.