Q:Angle valve holes are all crooked, as well as the impact?

Is the angle valve hole is crooked, or the wall hole is crooked, if the angle valve hole is crooked, may affect the service life,

Q:What are the structures of angle valves?

Structure of angle valve:Angle valve structure is relatively simple: angle valve is divided into shell, spool, handle three parts, there are two through the mouth, a water inlet, a waterAngle valve profile:Angle valve is angle globe valve, angle valve and spherical valve similar to its structure and characteristics are modified by the ball valve.

Q:What is the diameter of the G1/2 angle valve?

The first floor of the answer is very exciting, in hardware production, G1/2 external thread will be a lot of relaxation, select 20.7MM!

Q:How about the submarine triangle valve?

Submarine this brand is very good, safe, deodorant, practical, submarine is a good brand, reputation has been very good, ranking in the top three, very trustworthy.Submarine is a professional floor drain of this piece, very professional, in addition, angle valve is also very good, pure copper heart.Angle valve is also called triangle valve, angle valve, angle valve. This is because the pipe in the corner valve 90 degrees corner shape, so called "angle valve", "angle valve", "angle valve".Triangle valve concept:Angle valve body with water intake, water control, water outlet three mouth, so called triangle valve.Of course, now the angle valve in constant improvement, although it is still three mouth, but there is not angle shaped angle valve.Parameter description of the triangle valve:Old fashioned ball shaped triangle valveMedium and temperature: cold hot water of less than 90 degreesSurface finish: surface polished with nickel plated ChromeSpool material: low, slow open, multi-purpose copper or stainless steel; high-grade fast open for ceramic filmConnection type: G1/2 thread connectionSort:Triangle valve according to the distinction between hot and cold:"Cold" and "hot two" (to distinguish between blue and red flag) and triangle valve same manufacturer model in most of its material is the same no essential difference, the main purpose is to distinguish between warm and cold: hot and cold, mainly to distinguish which is the hot water, which is cold water. Only partially lowThe slow open triangle valve is the rubber ring spool, the rubber ring material can not withstand 90 degrees hot water, it is necessary to divide the cold and hot.

Q:Turn off the intake valve without dripping water; open the inlet valve and drip waterIt is not clear whether it is the inlet pipe or the angle valve

If the interface is leaking, you can remove the joints, wrap more raw materials, tighten the tape can be. Angle valve leakage is mostly caused by gasket wear, you can find a suitable thickness of rubber film change.

Q:Can the solar energy be supplied from the two angle valves below the gas heater?

his model is only 20-30 minutes longer than ordinary solar energy in the absence of the sun, while the single cabin takes 2-3 hours!

Q:My house is 1 kitchen 2 bathrooms, a kitchen vegetable washing basin, to install a water purifier, a kitchen po. Then a gas heater is installed in the kitchen and connected to 2 bathrooms through a hot water pipe. Among them, the public toilet a shower, a basin, a toilet, a squat toilet. Master bedroom, bathroom, a shower, a basin, a toilet.

Sink 2, kitchen Po 1, 2 basin faucet, toilet 1, their cumulative, no other. A angle valve, a hose

Q:Where do I need angle valves?

Angle valve, also known as triangular valve, angle valve, angle water valve, and more used in the decoration industry installation of water and electricity, is an important plumbing accessories.Angle valve mainly plays four roles:Switch out water outlet;

Q:The angle valve is wrapped with several circles of raw material

3, when you tie the tape to tighten the raw materials, so that the raw material with a tight stick attached to the thread, as far as possible tight, do not loose loose, wrapped around to use hand circling compression, you can also press while wrapping.4, as winding several layers, there is no hard and fast rules, to tighten, do not leak as the standard, but according to experience, usually need to wrap more than a dozen laps to ensure the sealing effect.

Q:Is the angle valve split hot and cold water?

Really is not, some just a red label angle valve handle. Just distinguish that from hot water to cold water.