Q:The newly purchased natural rubber tube is too large. How can it be removed?

Can buy some activated carbon in the box, the cost is not high, but also long lasting odor.00 grams of black tea bubble into the two washbasin hot water, dumbbells, rubber flavor placed in the pot, and open the window ventilation, 48 hours, dumbbell rubber flavor will be down more than 90%, the pungent odor is basically eliminated. - buy 800 grams of granular activated carbon, formaldehyde.

Q:How do you get the joint of the plastic pipe?

Special fittings for plastic pipes and special welding machines for plastic pipes are used. The pipe fittings and pipe heads are heated by melting machine and inserted together.

Q:What is a rubber core pulling method?

The hose shall be filled with water or gas at a pressure of 0.5 0.8N / mm before pouring concrete. At this point, the hose diameter can be increased by about 3mm. When pouring concrete, the vibrating bar should not touch the hose, and should check the pressure of the water meter regularly. If there is any change, the pressure must be filled.Smoke tube longer than tube core pulling slightly later. Before the pipe is pumped, the water is lowered and the pipe section is reduced, and the pipe can be drawn away from the concrete. The order of pumping is usually first, then first, then first, then straight.

Q:Can the rubber hose for the LPG cooker and gas cooker be general?

Whether the gas stove is the use of natural gas or liquefied gas, artificial gas, all can use the rubber tube, need to pay attention to is the pipe diameter and gas stove pipe diameter should be consistent, but also to the fixed ring frame with rubber tube, rubber tube is also too long existing problem of aging time, while the gas is there is a certain danger, recommend regular replacement of rubber tube

Q:Why should the high pressure hydraulic tube peel off the outer skin?

There are two reasons for stripping. One is that the inner diameter of the sleeve is the standard series, and that the outer diameter of the hose is not suitable, so it must be peeled. Two, after stripping, the sleeve can be directly pressed on the steel wire layer. The connection is reliable, and it is not easy to pull out.Whether or not to peel the rubber depends on the fit between the hose and the sleeve. Not every rubber hose is to be stripped.

Q:HDPE double wall corrugated pipe joint shall be made of elastic sealing rubber ring and socket joint interface. What are the requirements for rubber ring joint?

Before the interface, should check the rubber ring is complete, confirm the rubber ring placement and socket insertion depth.

Q:What are the gas hoses?

Go straight to the gas.There are 2 kinds of gas hose: one is made of black rubber thickened tube, and the other is stainless steel hose.Stainless steel hose is better, more than 10 years of life. Basically don't use it.Rubber life of 1 and a half years, 2 years later aging brittle, need to change.

Q:Why should the water stop strip be joined by heat instead of superposition?

Lap joint of rubber water stop belt is lap joint, this method is not allowed in engineering, glue glue and do not use overlay. In the case of splicing, it is equivalent to not doing any treatment at the joint. In the process of pouring, the sealing strip is prone to roll and twist.

Q:Is the rubber pipe joint installed in the middle of the pipe and pump for shock absorption?

A pump is a machine that transports liquids or pumps liquids. It will be the prime mover of the mechanical energy or other external energy transfer to the liquid, the liquid energy increase, mainly used to transport liquids including water, oil, alkali liquid, emulsion, suspension emulsion and liquid metal, but also transport liquid, gas mixtures and liquids containing suspended solids. Pump performance of technical parameters are flow, suction, lift, shaft power, water power, efficiency, etc.; according to the different principles of work can be divided into volume pumps, vane pumps and other types. Displacement pump is to use its studio volume changes to transfer energy; vane pump is to use the rotating blade and water interaction to transfer energy, there are centrifugal pumps, axial flow pumps and mixed flow pumps and other types.

Q:Acid burette and how to distinguish the basic buret

Acid burette glass valve cock, the basic buret is latex tube with glass balls