Hydraulic Floor Hinge/ Door Closer/Floor Spring for Glass Door/Floor Hinge for Glass Door FS-222

Ref Price:
Loading Port:
China main port
Payment Terms:
TT OR LC
Min Order Qty:
50 set
Supply Capability:
100000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

INTRODUCTION

    

Floor Spring is used for glass door, and they can be used together with door clamp. Floor Spring can be opened with double sizes, and on this point, it is different from that of door closer, which can just be opened by one size.  The key of technique lies on the loading seat under the main bearing, which decides the level of loading on the floor spring. Usually it can be opened from 300thousand or 1million times

 

 

FEATURES

 

u  Applicable for glass doors, wooden doors and the glass doors of metal frame and wooden frame.

u  Floor spring comply to EN 1154 and GB standard , and fire-rated EN1634 standard.

u  Maximum 500000 cycles tested without damage or maximum 7 years guarantee.

u  Double ways opening with smoothly movement, hold-open at 90°.

u  Closing speed and latching speed adjustable, latching point accurately at 0°

u  Stainless steel cover plate, satin or mirror surface available.

u  High quality casting iron floor spring body with 2 layers anti-rust coating.

u  All spindle types available for different countries.

u  Germany hydraulic machine oil and sealed rings, keep perfect working in cold temperature.

 

Hydraulic Floor Hinge/ Door Closer/Floor Spring for Glass Door/Floor Hinge for Glass Door FS-222

 

 

 SPECIFICATION

       Hydraulic Floor Hinge/ Door Closer/Floor Spring for Glass Door/Floor Hinge for Glass Door FS-222

     

INSTALLATION STEPS

 

1.      Draw lines and make floor spring pivot center and door-nip pivot coincide with each other.

2.      Drill holes on the floor according to the instructions. The sizes of the holes must tightly match the floor spring.

3.      Place the floor spring into the holes and position it.

4.      Raise the door leaf installed with door-nip, and insert the floor spring pivot into the hole of the door leaf.

5.     Adjust the screws at three directions. Make them vertical and the upper and lower pivot center coincide with each other.

6.      Adjust the speed of door closing.

7.      Put the decoration cover on the floor spring.

 

Hydraulic Floor Hinge/ Door Closer/Floor Spring for Glass Door/Floor Hinge for Glass Door FS-222

 

Package

Hydraulic Floor Hinge/ Door Closer/Floor Spring for Glass Door/Floor Hinge for Glass Door FS-222

 

Workshop

Hydraulic Floor Hinge/ Door Closer/Floor Spring for Glass Door/Floor Hinge for Glass Door FS-222

 

Testing Room

 

Hydraulic Floor Hinge/ Door Closer/Floor Spring for Glass Door/Floor Hinge for Glass Door FS-222

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What kind of production equipment does spring factory usually have?
Spring testing machines; fatigue testing machines; torsion testing machines; spring tension and compression testing machines
Q:What are the main functions of spring?
The storage and release of energy, for example, the clock spring bolt spring
Q:How should we choose the spring material?
Whether the spring is good or not is of great importance to the choice of the spring material. In general, selection of spring material, should take into account the load properties, spring force, various factors should be size, working conditions and price, etc.. Specific can follow the following principles: 1) in determining the shape and size of spring material, should be preferred dimensions behind national standards or standard stipulated, try to avoid using non standard materials. Although the spiral spring square or rectangular cross section material, the elastic deformation can be higher than, can make the small volume of the spring, for spring, in small space or under impact load but because of square or rectangular section material shortage, the price is higher, and the spring forming is difficult, so should be avoided. Ring section spring material diameter series see table 3-9. 2) the degree of cold plastic deformation of cold drawn spring materials is high. Most finished steel wires have reached the required mechanical properties when they leave the factory. The surface quality of the steel wire is high, and the manufacturing process of the spring is simple. For springs of medium or small spring or high fatigue life, the cold spring or cold drawn spring or steel wire or strip shall be selected as far as possible. Carbon spring steel wire (group I, group II, group II A, dish group) and important uses of 65Mn spring steel wire during the cold drawing process caused in large residual stress, the larger the size change after low temperature tempering, and thus affect the dimensional accuracy of the spring. For the bending radius of smaller tension and torsion spring, as well as smaller steel wire compression...
Q:Cold rolled coil spring spring and difference "
Coil is to burn the red, generally large diameter to coil
Q:What are the categories of springs?
The coil spring, the torsion spring, is a spring that bears torsional deformation, and its working part is tightly wound into a spiral shape. The torsion spring end is made of twisted arms of various shapes rather than rings.
Q:What's the spring material to?
65Mn, 55Si2Mn, 60Si2Mn, 50CrVA, 75, 85, 55CrMnA, 60Si2CrVA, 60Si2MnA, 70, 65, 50CrMo, 55SiMnMoVNb, 60SiMnMoA, 65Si2MnWA, 70Si3MnA, and so on
Q:Is spring steel manganese steel?
Manganese steel and spring steel are the names produced under different classifications. The spring steel is classified from its use, and manganese steel is classified from its constituents. Spring steel also contains manganese, which is a kind of manganese steel.
Q:How to distinguish between spring steel and stainless steel
Stainless acid resistant steel, or stainless steel, is made up of two parts: stainless steel and acid resistant steel. In short, steel that resists atmospheric corrosion is called stainless steel, and steel resistant to chemical corrosion is called acid resistant steel. Spring steel is a quality carbon steel, but it can rust.
Q:Stainless steel and spring steel hardness, who is hard?
Hardness is checked by indentation, not by pliers.Stainless steel, of course
Q:What kind of material does spring have?
Carbon spring steel: the material: 65#, 70#, 65Mn, 82B, 72A, 72B steel, is characterized by low plasticity, strong elasticity, anti stress ability. Application: mainly used for Simmons bed, car cushion, and all kinds of machinery, electric tools, stationery, sports equipment, torsion spring, spring, electrical equipment and other industries. Specifications: line diameter 0.20mm- GB4357-89 6.50mm. standard: carbon spring steel wire, national standard, main use: used to make cold formed in the cold state without hardening spring

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range