Q:There is no width of 30 cm wash basin cabinet

Of course not, wash basin is generally 55 width. Pots are generally the smallest 35

Q:how d i caulk around the sink it seems that im mentally challenged at caulking. i do all of the house repairs with ease just not this. its a circular sink and the old stuff failed after 10 years. i bought GE 3 hour silicone shower caulking to do it with the caulking gun. when i start applying it it looks good and every thing then i go to wipe it then it spreads onto the counter top and sides of the sink. then when im trying to clean it up with a rag it picks the caulking up fine but then takes out allot of the stuff i just put around the sink and looks un even. then by the time i clean one part it has started to dry then i go wipe the other part and it goes into balls. honestly i dont know how to do it. any help would be great.

When I was remodelling and putting in the bathroom sinks (3) I got a tip from my brother in law, mr fix it all. Dip your finger in rubbing alcohol, the kind for your skin to clean your lines of caulking up with. You can dip a rag in it or a paper towel and clean up the edges or where you smeared it. That will work. It cleans up, just fine that way. Try it. Good luck!

Q:what is the best drain cleaner for the bathroom sink?

A plunger will normally do the job. Fill the sink half with hot water and the pull the plug. Put the plunger over the drain pipe and pus hardactuallyly it is better to hit it with the palm of your hand. You mus block the overflow and also the drain plugs if the piping is connected to the sinks as well. If the plunger does not remove the blockage you can pour 1/2 a cup Costic soda (Sodium Hydroxide) in the drain plug and add some water, wait about 10 minutes and then use the plunger again. Be verycare full when working with costic soda. wear safety glasses as well as gloves. Do not let any costic soda deluted or un deluted come in contact with your skin or any part of your body. Do not add hot water to the costic soda it may put the system under pressure and burst some of the pipes. Do not use costic soda in a septec tank system it will kill all the buggs that work for you in the tank.

Q:How to choose the bathroom as a whole basin

The depth of the basin can be selected as needed. If you do not like the heavy feeling, you can choose the design of shallow, so suitable for small space bathroom.

Q:Am at wits end. Probably have to call a professional.The rubber seal on this Delta faucet is almost non-existent and somewhat leaking but not profusely Someone had suggested unscrewing the 2 faucets, did that, but then what next? The faucet itself is intact to the sink. Why did someone think it would lift out? It does not.The only way to get to it is from underneath and it is very tight space, the vanity is very small. The sink is in the way so I can't even see the underneath of the faucet itself from inside the cabinet, it is way back and like I said, the space is very very small. Looks like the sink probably has to be removed first? Such a pain for such a small job.Thank you.

hi, as staggering because it may sound, aspects would be extra much lower priced than a plumbers hard paintings. in case you do not sense delicate working in this fix, I comprehend, do hire a qualified plumber. reckoning on the are you reside in, i could guess seventy 5 to one hundred twenty five.00 hard paintings. that's if no matters arise at an analogous time as attending to the undesirable washer. in case you comprehend the type of faucet, call some community plumbers, ask for a coarse estimate to change the washers for that faucet. you will get a regularly occurring fee to your fix. better of success

Q:Wash the basin from the height of the number of appropriate

750mm-800mm is possible

Q:We recently renovated our entire house and we replaced all the faucets in the entire house. The electric hot water heater was also relocated. But now the water doesn't get hot in either bathroom sink. The faucets were purchased from Home Depot I have enclosed the link below. I don't want to call the contractor back out because I don't feel like dealing with him. It took him 8 month to complete the renovation that was suppose to take 2 months... Please help !! http://www.homedepot /Bath-Bathroom-Faucets-8-Widespread-Sink-Faucets/h_d1/N-5yc1vZ1xg1ZaqnbZ1z139uiZ1z139etZ1z11e3f/R-202044181/h_d2/ProductDisplay?langId=-1&storeId=10051&catalogId=10053

how far is the water heater from the sink, are you letting it run long enough, sometimes it takes a while. if the sink is connected to the heater, sooner or later it will heat up, if not, it isnt connected and you need to call the contracter. or you could get an undersink water heater just for that sink. you could also look under the sink to make sure the hot water water line is connected the the hot valve and it is open, although if it isnt there is probably a not good reason.

Q:how to umplug bathroom sink?

there are two options I suggest. First (and easiest,) give drano a try. That stuff has always worked for me. If that doesn't work, you should be able to take the s-trap ( the part of the drain pipe under the sink that dips before it goes through the wall.) Odds are that is where the clog is. Flush that piece out, or buy a new one. Then, check the pipe that leads from the sink to the s-trap for debris. Put it all back together. If the clog is further down the pipe, you may need a plumber.

Q:Tablet Decoration how to do, artificial stone surface decal how to do the process, where the film can buy

You are advised not to do or stainless steel pots higher than the table a little better because of such a clean and clean even if the basin and the table can be flattened, then the formation of a circle of grooves so easy to hide dirt and cause health cleanup is not completely from the outside The indecent indecentness

Q:About 10-12 years ago we had our bathroom sink resurfaced (I don't know what with, and it's now rather pliable/rubbery), and it's beginning to peel around the faucet area, and in some very small spots in the main part of the sink bowl. Is there a best way to remove the new surface, which is quite ugly peeling, to get back to the old surface? Thanks.

you're asking for more work than it's worth.